User manual CAMBRIDGE SOUNDWORKS DTT51

[. . . ] DeskTop Theater 5. 1TM Amplified Five Satellite/Subwoofer Speaker System With Dolby Digital Processor Installation and Operating Instructions © 1998 Cambridge SoundWorks, Inc. Safety & Regulatory Information The following sections contain notices for various countries: Notice for the USA FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, this notice is not a guarantee that interference will not occur in a particular installation. [. . . ] The satellites may be hung on the wall using the screw and wall anchors provided (see "Mounting The Speakers" page 7). , Do not be concerned if this placement is not practical. Any rear satellite placement to the left and right side of the listening position will provide strong directional and surround effects. C D E F 4 G The rear satellites may be installed on their convenient floor stands. While listening, the stands should be positioned to the left and right of your listening position (see Diagram G). The Floor Stands are small enough to be stowed underneath a desk when not in use. See page 7 for floor stand assembly instructions. Larger work surfaces can accommodate both front and surround pairs of satellites on their stands. Try the extreme corners of a desk using the Desktop Stands (see Diagram H). Also, you may attach the rear satellites under a desktop or at the sides of a desk using the hook and loop fasteners (see Diagram I). After you positioned the rear satellites, use the test sound to make sure each speaker can be heard clearly. The subwoofer's optimum position is on the floor against the wall under the computer desk. The nearer the subwoofer is to the corner of the room, the stronger its maximum bass output will be. We strongly recommend placing the subwoofer on the floor (see Diagram J). Leave at least 8 cm (3 inches) of space between the subwoofer face and a wall. Small objects in front of, but not touching the subwoofer (table legs, for instance) will have no effect on its sound If you have no available floor space, the subwoofer can be placed on a shelf, desktop or other sites, but its maximum output will be reduced. The subwoofer is magnetically shielded, allowing placement near computers or monitors. H I J 5 The Satellite Desktop Stands Install a Satellite Desktop Stand by inserting it into the "T"-shaped socket in the back of each satellite, feeding the cable through the stand's cut-out (see Diagram K) . Apply the five self adhesive feet to the base of the Desktop Stands (see Diagram L). The feet prevent a satellite from sliding across the desktop should it be inadvertently bumped or jostled. Note: If you wish to install the rear Satellites in the Floor Stands, do not apply the self adhesive feet to the base of their Desktop Stands. The Center Channel Stands The stands for the center channel speaker are installed by inserting the strut of the stand into the recess in the back of the Center Channel speaker (see Diagram L1). If using the Center Desktop Stand, apply the provided selfadhesive feet to it's bottom surface. The feet prevent a satellite speaker from sliding across the desktop should it be inadvertently bumped or jostled. Use the provided hook and loop fasteners to adhere the Monitor Stand to the top surface of the monitor (see Diagram L2). FRONT LEFT K L1 L2 Apply feet only to Center Desktop stand L 6 The Floor Stands The rear satellites (with their Desktop Stands attached) may be installed in their floor stands. Two of the six floor stand legs have a full length slot, with short notches opposite the slot at each end. [. . . ] You can get the latest program and driver updates from Creative Labs' bulletin board, 24 hours a day. Call 405-742-6600; use modem settings: Baud rate: Data bits: Parity: Stop bits: 300 to 14400 (V. 32/V bis) . 42 8 none 1 You can also send a FAX at 405-742-6633 or write us at: Technical Support Creative Labs, Inc. 1523 Cimarron Plaza Stillwater, OK 74075 To reach Creative Technical support via the Internet, visit our technical support web site at http://www. creativehelp. com, for troubleshooting help. For information about this product and other Creative Labs products, visit Creative Zone at http://www. soundblaster. com. [. . . ]