User manual CAMCO V8 11-2010

[. . . ] V O RT E X S I LV E R S E R I E S V8 USER MANUAL INFORMATION FOR USE FOR MODELS VORTEX SILVER SERIES V8 SSUM_GB_200-R_-200 The leading version of this brochure is the English one which shall prevail to the exclusion of the national translation on hand. Copyright 200 by CAMCO Produktions- und Vertriebs-GmbH für Beschallungs- und Beleuchtungsanlagen Fischpicke 5, D-57482 Wenden, Germany Telephone +49 (0) 2762 408-0 VIOERT EI E S X S LV R S E R Please visit our website www. camcoaudio. com for the latest version of this user manual. Please note that the leading version of CAMCO manuals is always the English one. P . USER MANUAL VORTEX SILVER SERIES V8 V O RT E X S I LV E R S E R I E S IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS . General The amplifier may only be used in accordance with the information provided in the user manual. [. . . ] IMPORTANT: When connecting speaker cabinets in parallel, always use all the contacts in both SPEAKON connectors. If not, this may cause permanent damage to the connectors and considerably reduce performance. 3. 4 Mains supply When mounting or connecting the amp, always disconnect it from mains. Only connect the V8 amplifier to an appropriate AC circuit and outlet in accordance with the requirements indicated in the second line on the rating plate. VORTEX-V8 120/230V~50/60Hz2100W 4400W/2 xxxxx Exemplary rating plates for a mains supply of 20/230 V AC 50/60 Hz. Power Supply Data: Voltage V8 20/230 V Mains Frequency 50/60 Hz Current 30/5 A Power Consumption 200 W NOTE: Even under normal conditions the mains current can reach levels up to 20 A (230 V), and 40 A (20 V), respectively; this could cause lamps to flicker if connected to the same mains as the amp. The impedance of the AC circuit should be less than 0, 57 to avoid flicker according to EN6000-3- "Electromagnetic compatibility ­ Part 3: Limits ­ Limitation of voltage changes, voltage fluctuations, and flicker in the public low-voltage supply systems ­ Equipment with rated current 75 A and subject to conditional connection". If in any doubt, consult your local power provider. Never attempt to measure this impedance level with your Ohmmeter. This may damage your meter and expose you to the risk of electric shock! P . 3 USER MANUAL VORTEX SILVER SERIES V8 V O RT E X S I LV E R S E R I E S 4 OPERATION 4. Screen User Interface Due to the advanced approach with the absence of any control knobs or switches, control of all parameters is done via the screen user interface. Screen User Interface Elements The screen user interface consists of four buttons and two selection bars. 2 6 Vertical Selection Bar (VSB) - scrolls through menu items 4. . 2 Handle the Selection Bars 3 4 6 5 MENU button ( ) - touch to leave the current sreen without changes - Hot key: touch and hold (2 s) to navigate to the Signal Monitor 2 ENTER button ( ) - navigate to the selected menu item, confirm changes 3 A button ( ) - select channel A 4 B button ( ) - select channel B 5 Horizontal Selection Bar (HSB) - increase/decrease values -Tip the VSB at the upper half to scroll upwards. -Tip the VSB at the lower half to scroll downwards. -Tip the HSB at the left half to decrease values. -Tip the HSB at the right half to increase values. P . 4 USER MANUAL VORTEX SILVER SERIES V8 V O RT E X S I LV E R S E R I E S 4 OPERATION 4. . 3 Hot key Functions The Hot key Functions give you a quick access to important setting screens. The Power Hot key is accessible from all menu levels and screens. Power Off Hot key: Touch and hold MENU and ENTER simultaneously (3 s). Touching again MENU and ENTER simultaneously will start Power Off-Sequence. Level Attenuator Hot key (from monitor screens 3. -3. 4): Touching the HSB opens the Level Attenuator Screen for a quick access to level adjustments. After adjustment you can step back to the previous screen by touching the MENU button. Mute Hot key (from monitor screens 3. 2-3. 4): Touching button A or button B let you directly jump to the Signal Monitor. Here you can mute/unmute each channel directly by touching button A or button B again. After adjustment you can step back to the previous screen by touching the MENU button. Signal Monitor Hot key Touch and hold MENU (3 s) let you directly jump to the Signal Monitor. [. . . ] Above 40 °C the speed is increased until it reaches its maximum value. P . 9 USER MANUAL VORTEX SILVER SERIES V8 V O RT E X S I LV E R S E R I E S 4 OPERATION 4. 2 Filter Cleaning The air intake on the front of your V8 amplifier is fitted with a removable filter system. If the filter becomes clogged, the unit will not cool as efficiently as it should and may result in reduced output levels. For changing the filter, no tools are required: first, gently slide the whole plastic filter assembly a few millimeters to the left and lift it from the front panel. Next, beginning on one of the long sides, carefully unclip the molded surround (4) from the cradle (2) and then carefully pull the CAMCO badge (5) out of the four fastening holes with both hands. Remove the foam filter (3) and clean it with a mild dishwashing detergent and warm water. [. . . ]