User manual CAME ARGO A1824

[. . . ] The total power consumption of 24 V accessories must not exceed 20W. Safety Photocells can be connected to obtain: -Re-opening during the closing cycle (2- C1); -Re-closing during the opening cycle (2-CX, see dip 8-9); -Partial stop, shutdown of moving gate, with activation of an automatic closing cycle (2-CX, see dip 8-9); -Total stop (1-2), shutdown of gate movement without automatic closing; a pushbutton or radio remote control must be actuated to resume movement; N. B: If an NC safety contact (2-C1, 2CX, 1-2) is opened, the LED will flash to indicate this fact; -Obstacle presence detection. When the motor is stopped (gate is closed, open or half-open after an emercency stop command), the transmitter and the control pushbutton will be deactivated if an obstacle is detected by one of the safety devices (for example, the photocells); -Safety test function. [. . . ] The control unit will now check the safety system every time an opening or closing command is given (see pag. Accessories which can be connected -Cycle lamp or courtesy light (60 Watt, see pag. 16); Other functions -Automatic closing: The automatic closing timer is automatically -4- activated at the end of the opening cycle. The preset, adjustable automatic closing time is automatically interrupted by the activation of any safety system, and is deactivated after a STOP command or in case of power failure; -Partial opening. Opening of the gate to allow for foot traffic; activated by connecting to terminals 2-3P and adjusted with the AP-PARZ. With this function, the automatic closing can vary in the following way: 1) Dip 12 set to ON: after a partial opening, the time for automatic closing functions independently of the adjustment of the TCA trimmer and of the position of Dip 1; it is set at 8 seconds. 2) Dip 12 set to OFF: after a partial opening, the time for automatic closing is adjustable only if Dip 1 is set to ON. The lamp which lights the manoeuvring zone: it remains lit from the moment the doors begin to open until they are completely closed (including the time required for the automatic closure). In case automatic closure is not enabled, the lamp remains lit only during movement (EEX), see p. "Master" refers to the motor that controls both the gates. On the control board of the 2nd motor, set dip-switch 11 to ON to make it the "slave" (1). - Make sure that the radio receiver is activated only on the MASTER board (2); - Wire the electrical connections and the normally used selections only on the MASTER terminal board (3); - Wire the electrical connections between the terminal boards, as shown in the Fig. A; - Make sure that all the dip-switches on the board of the 2nd motor are (OFF), except for dip 11 (4). NB: If the two coupled gates are of different sizes, the master function must be fitted to the motor control board installed on the longer door. 92 MHz (TOP and TAM series), position the jumper connection on circuit card AF43S as shown on the sheet. Plantear el código en el dip-switch C y el canal en D (P1=CH1 y P2=CH2, planteamiento por defecto) D P1 P2 1 2 3 4 1 2 3 4 5 6 7 8 9 10 P1 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 CH1 CH2 4 1 2 3 4 CH3 1 2 3 4 CH4 1 2 3 4 C T434M - T314M P1=CH1 P2=CH2 P3=CH3 P4=CH4 P2 1 2 3 CH1 CH2 CH3 CH4 T432S / T432SA / T434MA vedi istruzioni su confezione see instructions on pack voir instructions sur l'emballage Siehe Anleitungen auf der Packung. ver instrucciones en el embalaje P1 P3 P2 P4 impostare solo il codice set code only ne saisir que le code Stellen Sie nur den Code ein. Plantear sólo el código 1 2 3 4 5 6 7 8 9 10 C TAM T432 T434 T438 vedi foglio istruzioni inserito nella confezione TFM T132 T134 T138 T152 T154 T158 see instruction sheet inside the pack voir la notice d'instructions qui se trouve dans l'emballage Siehe Anleitungen, die der Packung beiliegen. [. . . ] Plantear sólo el código 1 2 3 4 5 6 7 8 9 10 C TAM T432 T434 T438 vedi foglio istruzioni inserito nella confezione TFM T132 T134 T138 T152 T154 T158 see instruction sheet inside the pack voir la notice d'instructions qui se trouve dans l'emballage Siehe Anleitungen, die der Packung beiliegen. B The first encoding operation must be carried out whilst keeping the J jumpers positioned for channels 1 and 2 as per fig. B for any subsequent settings on different channels. ENGLISH -While holding down key "CH1", press the control key on the transmitter after the signal LED lights up. [. . . ]