User manual CAME BK2200T

[. . . ] Dimensions of the ZL80 container 240 145 Dimensions of the BK2200T container 320 240 165 4 Tutti i dati e le informazioni quì contenute sono da ritenersi suscettibili di modifica in qualsiasi momento e a nostro giudizio 320 Emglish Tutti i dati e le informazioni quì contenute sono da ritenersi suscettibili di modifica in qualsiasi momento e a nostro giudizio 21 5 The pre-punched holes have a 20/21 mm diameter 295 5. 4 Spessori minimi e tipo cavi Connections Power supply line, 230/400V 3F Power supply line, 230V 2F Motors, 230/400V 2F/3F Motor, 24V Flashing lamp 230V Flashing lamp 24V Cycle/courtesy lights 230V Power supply accessories 24V Warning light 24V Output 24V “in motion” Safety contacts N. Control buttons End stop 2nd motor control Antenna connection (max 50m) Encoder connection (max 30m) Cable type Cable length 1<10 M 4G 1, 5mm² 3G 1, 5mm² 4G 1mm² 2 x 1mm² 2 x 0, 5mm² 2 x 0, 5mm² 3G 0, 5mm² Cable length 10<20 M 4G 2, 5mm² 3G 2, 5mm² 4G 1, 5mm² 2 x 1, 5mm² 2 x 1mm² 2 x 1mm² 3G 1mm² 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 3 x 1mm² 1 x 0, 5mm² Cable length 20<30 M 4G 4mm² 3G 4mm² 4G 2, 5mm² 2 x 2, 5mm² 2 x 1, 5mm² 2 x 1, 5mm² 3G 1, 5mm² 2 x 1mm² 2 x 1mm² 2 x 1mm² 2 x 0, 5mm² 2 x 0, 5mm² 3 x 1, 5mm² 1 x 1mm² FROR CEI 20-22 CEI EN 50267-2-1 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 2 x 0, 5mm² 3 x 0, 5mm² 1 x 0, 5mm² RG58 Insulated cable 2402C 22AWG PLEASE NOTE: If the cable length differs from that specified in the table, then you must determine the cable diameter on the basis of the actual power draw from the connected devices and depending on the standards specified in CEI EN 60204-1. [. . . ] Time > < > ESC 20 sec ENTER EXAMPLE PROGRAMMING FUNCTION PROGRAMMING FUNCTION the smaller ESC When than/ greater than <> symAuto Clo. Time > bols are on the TIME ESC 20 sec function, its values may < ESC be changed. €then press ENTER < < > > ENTER < PROGRAMMING FUNC To increase or reduce the value use the smaller > ENTER than/greater than keys ENTER PROGRAMMING FUNCTION ESC Auto Clo. Time < < 45 < ESC sec > > > ENTER ENTER …to exit the menu, wait 30 seconds, or press ESC, until the initial screen reappears …then press ENTER to confirm… Please note: when the menu is active the system cannot be used. 4 Description of menu items Language Select language: select the menu language among those available. Select LANGUAGE ENTER Italian > > English > > French > > Emglish German Spanisch Dutch Time intervals Time of operation: operating time intervals of the gearmotor during the opening phase or closing phase (from 10” o 120”) TIMES ENTER Oper. : automatic closing time following an opening command (from 1” to 120”). : automatic closing time following a pedestrian opening command (from 1” to 120”). ENTER > x3 Courtesy time TIMES Functions ENTER < 10 sec > < > Automatic Closing: activates or deactivates the automatic closing function FUNCTIONS ENTER > Automatic cl. ENTER > New user Vedere descrizione dettagliata Sensitive Safety Strip obstacle detector (obstruction detection sensor): adjusts the gate’s sensitivity, when obstructions are detected during motion. ENTER +oooo• < > Partial opening travel run: adjusts the partial opening travel run. Run ENTER < 40% < > > Web/Network Address: assigns a value of between 1 and 16 for purposes of software recognition. ENTER > x4 Network ID ENTER < > INFO 1 <-> 16 Version: Visualises the software version Number of cycles: visualises the number cycles made. Welcome message: to set the welcome message on the display. PROGRAMMING FUNCTION 1 Perform a complete opening run using (<>), until the complete opening occurs. > ESC < > ENTER ESC < > ENTER Carry out a complete closing run using (<>), until the leaf is completely closed. pROGRAMMING FUNCTION Do a full closing Run 4 5 Press ENTER to confirm. 6 – Set the gate leaf in motion for at least 3” PROGRAMMING FUNCTION 6 Set opening dir ENT:OK <>:move ESC < > ENTER ESC < > ENTER 7 Press ENTER to confirm. [. . . ] Press ENTER to confirm PROGRAMMING FUNCTION 1 Choose the function associated with the user (User Function or Partial Opening). A code will be required which may inserted with a remote control, a slide-through card or a transponder, depending on the type of sensors installed in the system at hand 3 Once the remote control or card code has been added, the word Memorised will appear on the screen (if the code has yet to be added), or the word On file (if the code has already been added). Cod In any case a window will appear asking whether we wish to add a new PROGRAMMING FUNCTION code or not. [. . . ]