User manual CAME TSP01

[. . . ] In order to avoid injury, therefore, you should take special care whenever handling these components. • Be sure to securely tighten nuts and other fasteners when setting up this electronic drum kit. In addition, be sure to proceed slowly when loosening nuts. [. . . ] • Be careful with the tips of supports, arms, screws, and the like. Fingers can easily be injured by sharp tips if these components are not handled carefully. • Do not place hands or feet under a kick pad or foot pedal. • Do not use the electronic drum kit’s rack to hold acoustic drums. Doing so could cause clamps to break and the drums to fall off, which in turn could lead to injury. 1. Remove the drum module clamp a and the left leg b from the left side of the rack. 2. Assemble the holder clamp for the hi-hat holder, ensuring that it is oriented as shown in the figure. Following this, reassemble the left leg b and the drum module clamp a. Hi-hat holder Holder clamp NOTICE: Usage Precautions • When connecting and disconnecting cables, be sure to hold the plug and not the cable itself. In addition, avoid placing heavy items on top of cables and do not allow them to touch sharp edges. Push each of the tom pads onto one of the rack’s Frame Push on Clamp bolt DTX522K Tom pad: TP70 Rod DTX542K Tom pad: XP70 Rod Base XP80 Snare Pad 3. Loosen bolts A to D as shown below to adjust the height and angle of the snare pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. Bolt B Bolt D Bolt C Bolt A Wing bolt Push on Tom holder Clamp bolt Push on Tom holder  Snare pad 1. 4 5 1. Arrange the hi-hat controller and the kick pad as shown in Example of standard assembly on the other side of this sheet. NOTICE Lay a drum mat (sold separately) on the floor underneath the hi-hat controller and the kick pad. Alternatively, you can place cardboard from the drum kit packaging or the like on the floor to prevent it from being scratched. Attach a clamp bolt to the snare pad and provisionally tighten (by five or six turns). Clamp bolt (tighten in the direction of the arrow) Underside of snare pad 3. Loosen bolts A to C as shown below to adjust the height and angle of each tom pad’s playing surface. When correctly positioned, be sure to securely retighten the bolts before proceeding to the next step. Bolt B Connect the pads to the drum module. Connect the output of each pad to the corresponding drum-module input. Bolt A Bolt C * DTX542K shown. Plug the straight ends of the nine-channel snake cable into the trigger input jacks ([qSNARE] to [oHI-HAT] and [HI-HAT CONTROL]) on the back of the drum module. • When using the standard setup, the stickers on each of the snake cable’s plugs will indicate the name of the corresponding pad. 2. Plug the L-shaped ends of the nine-channel snake cable into the corresponding pads. Locations of pad jacks Drum-module rear panel Assembling the drum module, cymbal pads, and hi-hat pad PCY100 Cymbal Pad PCY135 Cymbal Pad CRASH 4 3 2 1 7 6 5  Each cymbal and hi-hat pad 5. [. . . ] In the case of snare and tom pads, wrap the cables around the cable clips to prevent them from being pulled out. NOTICE HH CON HI HAT CRASH KICK SNARE TOM1 TOM2 TOM3 RIDE  Drum module Cymbal holder Excessive bending can damage pad cables. Ensure, therefore, that these cables are not bent at an extreme angle when wrapped around the clips. 1. Secure the module holder to the bottom of the drum module using the module holder screws. Module holder Module holder screws Bottom of drum module 3. Place the stopper on the cymbal holder. * If the key bolt was not sufficiently loosened in Step 1 above, it may not be possible to pass the stopper over the cymbal holder’s shaft. [. . . ]