User manual CAME ZCX10C

[. . . ] Display Programming buttons Memory roll connector 7 - Connector for R700 board 8 - HF card connector 9 - Terminal board 10- Power supply 11- Line Fuse 3. 1 15 mm~ English 2 insert the hinges into the housing (on the) left or right as preferred) and secure with the screws and washers supplied Assemble the spring-type hinges, they flow for rotating 3 Snap the cover over the hinges, then close and secure it using the screws supplied 4 Installation 4 . 1 Preliminary checks Installation must be carried out by qualified and expert personnel, fully respecting the current standards. [. . . ] : automatic closing time after an opening command. : automatic closing time after an pedestrian opening command TIMING ENTER > x3 Pedestrain ACT ENTER < 10 sec > < > Functions Automatic Closure: Enables/disables the automatic closing function FUNCTIONS ENTER > Auto Closing ENTER <ON > < > <OFF> Command 2-7: Sets the sequential- or stepper contact. FUNCTIONS ENTER > x1 Input 2-7 ENTER Open Close < > Open-Stop-Close User function: Sets to the user or the open-only command, or the function associated to the 2-7 command. > ENTER Dead Man x4 FUNCTIONS ENTER <ON > < > <OFF> ENTER <ON > < > <OFF> Tutti i dati e le informazioni quì contenute sono da ritenersi susciettibili di modifica in qualsiasi momento e a nostro giudizio CY Input : NC safety contacts input, with the possibility of associating the following functions: C1: Re-opening during closure, C2: Re-closing during opening, C3: Partial stop, C4: Obstacle delay interval, C6: Re-opening during closure due to sensitive rib. FUNCTIONS ENTER > x6 Input CY ENTER C1 > C2 > > C3 C6 > > C4 Disabled Entrance CX: Input of NC safety contacts with the possibility of associating the following functions:C1: Re-opening during closure, C2: Re-closing during opening, C3: Partial stop, C4: Obstacle delay interval, C6: Re-opening during closure due to sensitive rib. fUNCTIONS ENTER > x7 Input CX ENTER C1 > C2 > > C3 C6 > C4 Total stop: activates or deactivates Total stop. > Stop Button x8 FUNCTIONS ENTER ENTER Disabled > <ON > < > <OFF> Services test : Check the safety devices are correctly working and select which entrance they are connected to. ENTER > Safety Test x9 FUNCTIONS ENTER <OFF > > Enable on CX > > Enable on CX/CY Enable on CY Light socket: Socket for connecting the 220V flashing lamp, which can be set to two working modes, - Cycle: the flashing lamp works until the automation returns to its closed position. - Movement: The lamp flashes only with the automation moving. Flashing Light > x 10 FUNCTIONS ENTER ENTER Cycle Movment < > Detects obstacle: During closure with obstacle present, the automation does not move FUNCTIONS ENTER > x 11 Obstacle Pres. (Dead man Clos): Enables/disables the ‘Person present during closing’ function. 4 Menu items Radio/Users New User: Creates new users RADIO/USER ENTER > Add New User To see detailed description English Change User: For changing the functions associated to the user. Edit User > ENTER x1 RADIO/USER To see detailed description Remove user: Removes a user from the system. 5 empty < > Save memory: Save the users in the memory roll > ENTER User Backup x3 RADIO/USER ENTER ENTER Writing . Load memory: Loads the data saved from the memory roll. > ENTER User Restore x4 RADIO/USER ENTER ENTER Reading . [. . . ] If you don’t install the appropriate decoding board, you won’t be able to add any users. 1 2 From the Radio/Users menu, select New User and confirm with ENTER PROGRAMMING FUNCTION Select the function to associate to the user between User function and Partial opening, then confirm with ENTER. pROGRAMMING FUNCTION L LINGUA < inked Functio > < Add < New LINGUA U s e r> > < User F u n c t i o n> ESC < > ENTER ESC < > ENTER . [. . . ]