User manual CANDY CD 622

[. . . ] Please read this booklet carefully as it provides important information regarding the safe installation, use, and maintenance of the machine, together with some useful advice on how to achieve the best results from your dishwasher. For future reference please keep this instruction booklet in a safe place. Contents Safety advice Setting up, installation Opening the door Water softener unit Adjusting the upper basket Loading the dishes Information for test laboratories Loading the detergent and rinse aid Cleaning the filters Some practical hints Routine cleaning and maintenance Description of the controls Technical data Operating the programmes and special functions Programme selection Identifying minor faults page page page page page page page page page page page page page page page page 4 5 8 9 11 12 16 16 18 19 20 22 22 23 24 26 Guarantee & After Sales Service This appliance is supplied with a guarantee certificate which offers a free one year labour guarantee and a free five year parts guarantee - see the guarantee certificate for further details. Remember to post part A of the guarantee certificate within 10 days of the purchase date to register your guarantee with us. Part B should be filled in and retained by you, to be shown to the GIAS service engineer if required. [. . . ] For the machine to work properly, the door should not be opened while it is in operation. 8 - *The water softener unit is set in the factory at level 2, as this is suitable for the majority of users. If your water is at level 0, you need not use any regenerating salt, nor need you make any adjustment, as your water is soft. According to the degree of hardness of your water, regulate the softener unit in the following way: - remove the lower rack. Unscrew and remove the cap from the salt dispenser located in the bottom of the tub (Fig. A "1"); - Turn the selector screw to the required position with a screwdriver or a knife. TYPE 1 TYPE 2 9 Loading the salt The dishwasher is fitted with a softener which clears the water of lime which could cause scale and damage the dishwasher. On the bottom of the machine there is a container for the salt for regenerating the softener. The filter medium of the softening plant must be reactivated with dishwasher water softener regenerating salt. Other types of salt contain small quantities of insoluble particles which over a long period of time may affect and deteriorate the softener performance. To add salt, unscrew the cap of the container on the bottom and then refill the container. During this operation a little water will overflow; but keep adding salt until the container is full. When the container is full, clean the thread of salt residue and retighten the tap. Check the rinse aid level through the indicator eye which is situated in the centre of the dispenser (4). Loading the detergent and the rinse aid. Filling the detergent container It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid or tablet form. Finish gives very good results and can be easily obtained. Unsuitable detergents (like those for washing up by hand) do not contain the proper ingredients for use in a dishwasher and stop the dishwasher from working correctly. Normal wash The detergent container is inside the door (fig. If the lid of the container is closed press the button to open. At the end of every wash cycle the lid is always open and ready for the next time the dishwasher is used. The amount of detergent to be used varies according to how dirty the dishes are and on the type of dishes to be washed. We advise using 20-30 gr of detergent in the wash section of detergent compartment (1). After pouring the detergent into the container close the lid. Since not all detergents are the same the instructions on the boxes of detergent can vary. We should just like to remind users that too little detergent does not clean the dishes properly whilst too much detergent will not produce better results and is also a waste. [. . . ] Both the door lining and the tank lining are in stainless steel; however, should spots caused by oxidation occur, this is probably due to a high level of iron salts presents in the water. The spots can be removed with a mild abrasive agent; never use chlorine based materials, steel wool, etc. WHEN CYCLE IS FINISHED After every wash it is essential to turn off water supply and to switch off the machine by pressing the On/Off button to the off position. If the machine is not going to be used for some time, it is advisable to follow these rules: 1. do an empty wash with detergent in order to clean the machine of any deposits. [. . . ]