User manual CANDY CDP 2D35W-47

[. . . ] Any faults arising from operation at incorrect voltage. Any faults arising from incorrect operation of the machine. The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. AFTER SALES SERVICE For service and repairs call your local engineer on our national telephone number: GIAS Service Support Service Tel: 08444 995599 (Eire 0818 200021) 12 DESCRIPTION OF THE CONTROL PANEL A B C D E "ON/OFF" button "PROGRAMME SELECTION" button "DELAY START" button "EXPRESS" option button "ALL IN 1" option button F G H I "START"/"RESET" button (start/cancelling programme) "OPTION SELECTION" lights DIGITAL DISPLAY Programme guide DIMENSIONS With working top Width x Height x Depth (cm) Depth with door open (cm) EN 50242 place load Capacity with pans and dishes Water supply pressure (MPa) Fuse / Power input / Supply voltage 60 x 85 x 60 120 Without working top 59, 8 x 82 x 57, 3 117 13 8 persons Min. [. . . ] Salt empty alert Programme end A 5 second alarm will sound (if not muted) 3 times at 30 second intervals to signal that the programme has ended. the dishwasher will automatically switch off. 15 If your dishwasher requires filling with salt, the display will show and flash "SL" when the dishwasher is switched on. The appearance of white stains on dishes is generally a warning sign that the salt container needs filling. "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. Alarm mute for the PROGRAMME END The alarm for the programme end may be muted as follows: Proceed as follows to set a delayed start: ■ Press the "DELAY START" button ("00" will appear on the display). IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. –  Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). –  To start the countdown, press the "START" button. The display will show the time remaining to the begin of the programme. At the end of the countdown, the programme will automatically start and the length of the selected cycle will be shown in the display. proceed as follows to cancel a delayed start: 2. Keep the "PROGRAMME SELECTION" button pressed for at least 15 seconds (during this time 2 audible signals will sound). Release the button when the second audible signal sounds ("b1" will appear on the display to indicate that the alarm is on). –  Hold the "RESET" button down for at least 3 seconds. "00" will appear on the display and some audible signals will sound. Press the same button again ("b0" will appear on the display to indicate that the alarm is off). ■ The delayed start and the selected programme will be cancelled. Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. Press the same button again ("A1" will appear on the display to indicate that the memorization is on). Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. [. . . ] N/A = OPTION NOT AVAILABLE Dishwasher Cleaner This programme should be used periodically with = "IMPULSE" programmes 18 Check list Detergent for washing Detergent for soaking (Prewash) Check salt container Programme contents Hot rinse with rinse aid Avarage duration in minutes Special function buttons available * "DELAY START" button With cold water (15°C) -Tolerance ± 10%- “EXPRESS” button Second cold rinse ••••• •••• •••• ••••• •••• ••••• •••• •••• • * 75°C 60°C 55°C 45°C 45°C 65°C 50°C 55°C 130 120 80 170 85 59 24 240 5 YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES N/A YES N/A YES YES YES YES YES 70°C 45 WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS AUTOMATICALLY DISPLAYED WHILE THE PROGRAMME IS RUNNING. 19 "ALL IN 1" button Check rinse aid dispenser First cold rinse Cold pre-wash Hot pre-wash Main wash Clean filter AQUASTOP-SYSTEM The water-stop device protects against water damages caused by leaks on the fill hose which could develop due to natural ageing of the hose. In the water-stop system the leaking water fills the corrugated hose and activates a stop valve which cuts off the water supply to the machine. This fault is shown by a red sector on the window . [. . . ]