User manual CANDY CDP2LS36EA

[. . . ] Any faults arising from operation at incorrect voltage. Any faults arising from incorrect operation of the machine. The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. AFTER SALES SERVICE For service and repairs call your local engineer on our national telephone number: GIAS Service Support Service Tel: 08444 995599 (Eire 0818 200021) 12 DESCRIPTION OF THE CONTROL PANEL A B C D E "ON/OFF" button "PROGRAMME SELECTION" button "DELAY START" button "EXPRESS" option button "ALL IN 1" option button F G H I DIMENSIONS "START"/"RESET" button (start/cancelling programme) "OPTION SELECTION" lights DIGITAL DISPLAY Programme guide Width x Height x Depth (cm) Depth with door open (cm) 59, 8 x 81, 8 ÷ 89, 8 x 57 117 TECHNICAL DATA EN 50242 place load Capacity with pans and dishes Water supply pressure (MPa) Fuse / Power input / Supply voltage 13 8 persons Min. [. . . ] This programme is recommended for light soil washes, and for slightly wet dishes that are not fully dry, & improved drying results. We advise you to leave the door of the Dishwasher half-open at the end of the cycle, to allow for a natural circulation of air inside the dishwasher. "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. Proceed as follows to set a delayed start: ■ Press the "DELAY START" button ("00" will appear on the display). – Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). – To start the countdown, press the "START" button. The display will show the time remaining to the begin of the programme. At the end of the countdown, the programme will automatically start and the length of the selected cycle will be shown in the display. By pressing this button, the selected washing programme is modified to get best performance from combined detergents (furthermore, the salt empty alert will be de-activated). Proceed as follows to cancel a delayed start: ■ Hold the "RESET" button down for at least 3 seconds. "00" will appear on the display and some audible signals will sound. ■ The delayed start and the selected programme will be cancelled. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). Keep the "PROGRAMME SELECTION" button pressed for at least 30 seconds (during this time, 3 audible signals will sound). Release the button when the THIRD audible signal sounds ("A0 " will appear on the display to indicate that the memorization is off). Press the same button again ("A1" will appear on the display to indicate that the memorization is on). Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. To disable the memorization, follow the same procedure. IMPORTANT This dishwasher is equipped with an anti-overflow safety device which will automatically discharge any excess water should a problem occur. To ensure the correct operation of the anti-overflow safety device, we recommend that the dishwasher is not moved or tilted during operation. If however it is necessary to tilt or move the dishwasher, please ensure that the washing cycle is complete and that there is no remaining water inside the dishwasher. 16 Alarm mute for the PROGRAMME END The alarm for the programme end may be muted as follows: IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. [. . . ] N/A = OPTION NOT AVAILABLE Dishwasher Cleaner This programme should be used periodically with = "IMPULSE" programmes 18 Check list Detergent for washing Detergent for soaking (Prewash) Check salt container Programme contents Hot rinse with rinse aid Avarage duration in minutes Special function buttons available * "DELAY START" button With cold water (15°C) -Tolerance ± 10%- “EXPRESS” button Second cold rinse ••••• •••• •••• ••••• •••• ••••• •••• •••• • * 75°C 60°C 55°C 45°C 45°C 65°C 50°C 55°C 130 120 80 190 85 59 24 240 5 YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES N/A YES N/A YES YES YES YES YES YES YES YES 70°C 45 WITH HOT WATER THE TIME REMAINING UNTIL THE END OF THE PROGRAMME IS AUTOMATICALLY DISPLAYED WHILE THE PROGRAMME IS RUNNING. 19 "ALL IN 1" button Check rinse aid dispenser First cold rinse Cold pre-wash Hot pre-wash Main wash Clean filter AQUAPROTECT – PROTECTED INCOMING WATER PIPE The main inlet pipe is contained within a protective transparent hose. In the event of damage occurring to the main inlet pipe any water leakage is retained within the transparent hose. If water has leaked from the main inlet pipe there will be a visible sign within the transparent hose. [. . . ]