User manual CANDY CPG75SWPX

[. . . ] Any spillage should be removed from the lid before opening. The hob surface must be allowed to cool down before closing the lid. This appliance is not intended to be operated by means of an external timer or separate remote-control system. The means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. [. . . ] Intensive and prolonged use of the appliance may require extra ventilation, such as the opening of a window or an increase in speed of the electric fan, if you have one. If a hood can not be installed, an electric fan should be fitted to an outside wall or window to ensure that there is adequate ventilation. The electric fan should be able to carry out a complete change of air in the kitchen 3-5 times every hour. The installer should follow the relevant national standards. Warning - this appliance must be earthed This appliance is designed for domestic use only. Connection to the main supply must be made by a competant electrician, ensuring that all current regulations concerning such installations are observed. The appliance must only be connected to a suitably rated spur point, a 3 pin 13 amp plug/socket is not suitable. A double pole switch must be provided and the circuit must have appropriate fuse protection. Further details of the power requirement of the individual product will be found in the users' instruction and on the appliance rating plate. In the case of built-in product you are advised, should you wish to use a longer cable than the one supplied, that a suitably rated heat resistant type must be used. The wiring must be connected to the mains supply as follows: Note: We do not advocate the use of earth leakage devices with Electric cooking appliances installed to spur points because of the You are again reminded that the Appliance must be correctly earthed, the manufacturer declines any If an appliance is not fitted with a supply cord and a plug, or with other means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under overvoltage category III conditions, the instructions shall state that means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules. These instructions are for qualified personnel, installation of equipment must be in line with the relevant national standard. Only: by law the gas installation\commissioning must be carried out by a "Gas Safe" installer) All work must be carried out with the electricity supply disconnected. The rating plate on the hob shows the type of gas with which it is designed to be used. Connection to the mains gas supply or gas cylinder should be carried out after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated see the instructions in the following paragraphs to change gas setting. For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. Use only pipes, washers and sealing washers which comply with the relevant national standards. For some models a conic link is furnished to outfit for the installation in the countries where this type of link is obligatory; in picture 8 it is pointed out how to recognize the different types of links (CY = cylindrical, CO = conic). In every case the cylindrical part of the link has to be connected to the hob. When connecting the hob to the gas supply via use offlexible hoses please ensure that the maximum distance covered by the hose does not exceed 2 metres. The flexible tube shall be fitted in such a way that it cannot come into contact with a moveable part of the housing unit (e. [. . . ] AVERTIZARE: Nu lsai nesupravegheate recipientele în care preparai alimente cu ulei sau grsime, deoarece exist pericol de incendiu. ?n cazul în care cablul de alimentare este deteriorat, acesta trebuie înlocuit cu un cablu special de ctre o persoan calificat de la un centru de service autorizat ATENIE: Pentru a se evita orice pericol ca urmare a resetrii dispozitivului de siguran, acest aparat nu trebuie alimentat prin intermediul unui echipament de întrerupere extern, cum ar fi un programator sau un alt tip de circuit care este pornit i oprit periodic de ctre un alt dispozitiv. Plita poate fi instalat în orice blat de lucru care rezist la o temperatur de pân la 100°C i are o grosime de 25-45 mm. Dac exist un spaiu care este accesibil între plita incorporabil i cavitatea de sub aceasta, este recomandat s fie fixat un panou de izolare (din lemn sau un material similar) (Figura 3). [. . . ]