User manual CANDY CTI 46 B

[. . . ] R R PE SR SR SR SR UR H I R UR SR SR IE GB 39 INSTRUCTIONS FOR THE INSTALLER INSTALLATION The Purchaser is responsible for the installation of the hob. The Manufacturer does not accept any responsibility for any damage or loss resulting from incorrect installation, and as such this will not covered by the Manufacturer's Guarantee. The hob may be installed in any worktop which is heat resistant to a temperature of 100 C, and has a thickness of 25 - 45 mm. The dimensions of the insert to be cut out of the worktop are in shown in Fig. [. . . ] Do not search for a leak with a naked flame. 42 GB IE ELECTRICAL CONNECTION Check the data on the rating plate, located on the outside of the unit, to ensure that the supply and input voltage are suitable. Before connection, check the earthing system. If this regulation is not complied with, the Manufacturer will not be responsible for any damage caused to persons or property. If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. The earth wire is coloured yellow/green. Where the Hob is connected direct to the electricity supply, a circuit breaker must be fitted with at least a 3 mm contact spacing when in the open position. If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. The earth wire ( green a yellow coloured) must be at least 10 mm longer than the live and neutral wires. The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check rating plate for the power details and ensure that the power supply cord is of the type H05RR-F, H05VV-F, H05V2V2-F. MAINS SUPPLY LIVE EARTH L BROWN WIRE GREEN/YELLOW WIRE BLUE WIRE POWER CABLE NEUTRAL N GAS CONNECTION These instructions are for Fitters qualified for installation of equipment in line with the relevant national standard. All work must be carried out with the electricity supply disconnected. Once the air is correctly set secure the screw over the tube ( fig. 7). For dimensions X see table of gas consumption BURNER FIXING SCREW SMALL MEDIUM LARGE BURNER CAP AIR REGULATION SCREW DOUBLE RING MAXI FISH Fig. 8 REGULATING THE MINIMUM FLAME After lighting the burners, turn the control knob to the minimum setting and then remove the knob (this can easily be removed by apply a gentle pressure). Using a small Terminal type screwdriver the regulating screw can be adjusted as in Fig. Turning the screw clockwise reduces the gas flow, whilst turning it anticlockwise increases the flow Use this adjustment to obtain a flame of approximately 3 to 4 mm in length and then replace the control knob. When the gas supply available is LPG (Bottle gas)- the screw to set the idle flame must be turned (clockwise) to the end stop. Screws regulating (for differend models) Fig. 9 IE GB 45 When you have carried out the new gas regulation, replace the old gas rating plate on your appliance with one (supplied with hob) suitable for the type of gas for which it has been regulated. USE OF HOB USER INSTRUCTIONS This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responsible for any damage or loss resulting from improper use. USING THE GAS BURNER To ignite the burners, place a lighted taper close to the burner, press in and turn the control knob anti-clockwise. If the burners have not been used for a couple of days, wait for a few seconds before lighting the burner, this will allow any air present in the pipes to escape. For appliances fitted with electronic ignition carry out the following: push in and turn the knob anticlockwise to the 5 symbol. [. . . ] setting ceramic element 0 1 2 3 4 5 6 0 1 2 3 4 The light indicates the hotplate is on irrespective of the power setting. In the vetroceramic hobs a residual heat indicator light comes on and remains lit till the hob plate is cooled down. A neon indicator light adjacent to the control knob will glow when the electric plate is in use. The additional electric hotplate/ring ( 80 mm) where featured is turned on and off by pressing 0/I button, this hotplate has a fixed heat setting. [. . . ]