User manual CANDY HDPN1L360OW

[. . . ] We are proud to offer the ideal product for you and the best complete range of home appliances for your daily routine. Carefully read this manual for correct and safe appliance use and for helpful tips on efficient maintenance. Only use the dish washer after carefully reading these instructions. We recommend you always keep this manual to hand and in good condition for any future owner. [. . . ] If the machine is left in places where the temperature is below 0°C any water left inside the pipes may freeze. Wait until the temperature rises above zero and then wait for about 24 hours before. A ON/OFF button B "PROGRAMME SELECTION" button/ENROLMENT Wi-Fi C "SMART DOOR" option button D C+E CHILD LOCK E "DELAY START" button F Reset" button for "SALT EMPTY" light G "START/RESET" button H "SALT EMPTY" light I "PROGRAMME STATUS" lights/"DELAY START" time lights L "SMART DOOR" light M "PROGRAMME SELECTION" light N "ADDISH" light Place settings (EN 50242) Capacity with pans and dishes Water supply pressure (MPa) PROGRAMME SELECTION Next time you switch on the AND SPECIAL FEATURES appliance L To turn the appliance on and off, press the ON/OFF button (for at least 3 seconds). At the end of the cycle, remember to switch off the appliance using the ON/OFF button, then remove the plug and close the water supply. Hold down the ON/OFF button for about 3 sec. To turn the machine on, and the "P3"programme indicator light will come on. If you have turned on the programme memorisation function, the indicator light corresponding to the last programme completed will appear on the display. First time you switch on the appliance L Connect the machine to the power supply. L Open the door, put the dishes to be washed inside, and close the door again. L Press the "ON/OFF" button and hold for about 3 seconds. L At this time only the "ON/OFF" and "PROGRAMME SELECTION" buttons will be active, and all the programme indicator lights will come on for 3 sec. After this only indicator light "P3" will stay on, and all the buttons will still be active. l Choose a programme with the "PROGRAMME SELECTION" button. L If you wish to select an option, press the corresponding button (the indicator light representing the selected option will come on). L Press "START/RESET" and a signal will sound, the indicator light corresponding to the selected programme will stay on and the wash indicator light will come on. If the programme is started with the door open, a signal will sound 5 times, and the programme will be started automatically once the door has been closed. From the Settings menu, you can adjust various parameters to suit your washing requirements. Entering the Settings menu l Turn on the dishwasher by holding the "ON/OFF" button down for about 3 sec. L Hold down the "PROGRAMME SELECTION" and "ON/OFF" buttons for about 5 sec. L All the indicator lights will flash for 5 sec. l The settings will be displayed: - Lime scale prevention settings appear when the indicator light comes on in the corresponding programmes. If they are all off, the level is set to "S0". [. . . ] To ensure the correct operation of the overflow safety device, we recommend not moving or tilting the dishwasher during operation. Should it be necessary to tilt or move the dishwasher, please ensure that the washing cycle is complete and that no water remains inside the appliance. Dishwasher does not fill with water Plug not connected to wall socket O/I button not pressed Door is open no electricity See point 1 The water tap is closed The water supply hose is bent The filter of the water supply hose is clogged Filter is dirty Drain pipe is bent The drain pipe extension is not correctly connected The outlet connection on the wall is pointing downwards not upwards Position of the drain pipe is too low Lift drain pipe to at least 40 cm above floor level On electronic appliances without a display: one or more indicator lights flashing quickly The dishes are not completely dry Item prevents arms from rotating Filtering plate and filter very dirty Turn on the tap. Bottom of saucepans have not been washed well Edge of saucepans have not been washed well spray arms are partially blocked The dishes have not been loaded properly The end of the drain pipe is immersed in water An incorrect amount of detergent has been measured out, or the detergent is old and hard The cap of the salt container is not closed properly The wash programme is not thorough enough Burnt on food remains must be soaked before putting pans in dishwasher reposition saucepans Remove spray arms by unscrewing ring nuts clockwise and wash under running water Do not place the dishes too close together The end of the drain pipe must not come into contact with the outflow water Increase the measure according to how dirty the dishes are, or change detergent Choose a more vigorous programme , stop the detergent dispenser from opening Position dishes so as not to obstruct the dispenser The dishes knock against one another The revolving arms knock against the dishes Should the fault persist, contact the Technical Assistance Centre Leave the dishwasher door ajar at the end of the wash program to allow the dishes to dry naturally : Should any of the above situations result in a bad wash performance or insufficient rinsing, remove dirt deposits from the dishes by hand since the final drying cycle hardens the dirt, making it difficult to remove with a subsequent wash. [. . . ]