User manual CANDY P 604

[. . . ] 1 1 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 2 UNPACKING THE APPLIANCE Inside the appliance you will find a plastic bag containing the fixing brackets to install the hob in the worktop. RECOMMENDATIONS PLEASE READ THE FOLLOWING CAREFULLY IN ORDER TO GET THE BEST FROM YOUR APPLIANCE. Please keep the operating and installation instructions in a safe place for future reference. Before fixing the hob, note the serial number of the appliance just in case you may require repairs from after sales service organisation. . [. . . ] Strip the end of each conductor of the supply cord to a 10 mm length, by taking in account the requested length of the cord for the connection on the terminal block. According to the installation and with the help of shunt bars, fix the conductor as shown on the chart. Engage the earth wire yellow/green on the earth terminal, tighten the nut and verify the continuity of the earth. Fix the cover. 5 INSTALLATION: "ELECTRICAL CONNECTION" 1rst Phase Shunt Shunt Neutral Shunt Earth 1rst Phase 1 - 2 Shunt 2 - 3 Shunt 2nd Phase 4 - 5 Shunt Earth 1rst Phase 1 - 2 Shunt 2 - 3 2nd Phase Shunt 4 - 5 3rd Phase Earth 1rst Phase 1 - 2 2nd Phase 3rd Phase 3 - 4 Neutral 5 Shunt Earth 1 2 3 4-5 IMPORTANT : Blue wire = Neutral Yellow/green wire = Earth For the connection to the terminal block, you must : . do not forget to fix the earth wire (yellow/ green) on the earth terminal n° 6. Example of connection Three phase 220-240V3~ : The earth wire must be clipped at this place. Tighten the nut fully home. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INSTALLATION: "BUILDING-IN" Both the unit into which the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower part of the casing is adjacent to an area normally accessible when handling or cleaning, fit a heatproof partition 1 cm below the base of the casing, with a 10 x 10 cm opening in the rear right-hand corner, to avoid any risk of burning or damage. There should also be a 5 cm gap between the appliance and all adjacent vertical surfaces. A foam adhesive seal is supplied with the hob. Stick this seal under the edge of the body as near as possible to the outer edge of the hob. Press round the edges of the hob, so that the seal flattens out and ensures an air tight seal. Fitting the seal Top view of the hob SEAL Building-in according to TYPE Y (Norm EN 335-2-6) 7 INSTALLATION: "BUILDING-IN" The body of the hob is fitted with 4 location holes to take the fixing brackets that secure the intended to fix the hob in the unit. Place the 4 fixing brackets in such a way that the hob surface is placed perfectly in the support unit. Location for fixing brackets Fixing bracket 8 PRESENTATION PL 604 / TECHNICAL DATA 4 ELECTRICAL HOT PLATES Speed protected hot plate 1500 W - Ø 145 Speed protected Hot plate 2000 W - Ø 180 Speed protected Hot plate 1500 W - Ø 145 Speed protected hot plate 2000 W - Ø 180 Power-on indicator lights Overall dimensions (cm) : Width : 59 Depth : 51 Building-in dimensions (cm) - (see chapter "Installation") Width : 56 Depth : 48 Total electrical power : 7 kW In order to improve the quality of the products, CANDY may carry out modifications linked to technical improvements. Appliance meeting with the standard CEE 89/336, and 73/23. 9 THE HOT PLATE THE RAPID SELF-PROTECTING ELECTRIC HOT PLATE This is a cast-iron hot plate, controlled by a 7 position switch. As with the previous hot plate, each position corresponds to a permanent and progressive temperature according to the marks 1, 2, 3, 4, 5 and 6. An internal thermostat cuts off of the power supply if there is any overheating. (If, for example, a hot plate is working without a pan on it). BEFORE USING THE ELECTRIC HOT PLATE : · Before using the electric hot plate for the first time, let it heat up for a few minutes, without a pan, at maximum temperature to let the protective coating harden. HOW TO USE : · For best results, it is advisable to start on the maximum heat and then turn back to an intermediate temperature taking into account the type and volume of the food. · The power-on indicator light comes on to show that the hot plate is working. · To stop it, turn back the knob until position " ". THE DIFFERENT TEMPERATURE SETTINGS : below are a few examples which are given as guidelines. When you become more familiar with the appliance, you will be able to choose settings to suit your own personal tastes and requirements. Positions 1 2 3 4 5 6 Very low Low Moderately Medium High Very high Some tips . . . . . [. . . ] You can use a special product to clean stainless steel which is available in stores. THE KNOBS For thorough cleaning, the control knobs can be removed by pulling them upwards. Clean exclusively with soapy water and dry well before replacing them. THE HOT PLATE Heat it for a while if necessary, to burn the deposits. After switching off and cooling down of the plate, wipe it with an absorbing paper. In any cases, it is important to protect the hot plate from humidity. [. . . ]