User manual CANDY PA640-2 F

[. . . ] 12 · USING THE APPLIANCE The different gas burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Igniting and setting the burner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 General maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 2 UNPACKING THE APPLIANCE Inside the appliance, you will find : · a plastic bag containing : - the new jets for the gas modification, if required, - the fixing brackets with screws to install the hob in the worktop, and, · a spanner to change the jets if the factory gas setting does not correspond to your installation requirements. RECOMMENDATIONS PLEASE READ THE FOLLOWING CAREFULLY IN ORDER TO GET THE BEST FROM YOUR APPLIANCE. [. . . ] To gain access to the air rings on the hob burners: remove the pan support, the burner cap and body of the relevant burner. The air ring is located at the lengthening of the burner unit which is fixed by a screw (see drawing). unscrew the screw that holds the air flow adjuster, . set the correct distance according to the air adjuster protrudes, . secure the screw when the operation is completed. Semi-fast burner 1, 45 kW or Fast burner 2, 5 kW Quota X Fast burner 3, 2 kW Quota X Air ring Screw Air ring Screw Quota "X" in mm of the air ring according to the gas setting G20-20 mbar G25-25 mbar G30 28-30 mbar G31 37 mbar Semi-fast Fast 6 Fast Semi-fast 10 6 0 0 0 0 7 14 9 7 14 7 INSTALLATION: "BUILDING-IN" BUILDING-IN : both the unit into which the hob will be fitted and any adjacent kitchen furniture must be made from heat resistant material and fixed with heat resistant adhesive. If, when installing the hob, the lower part of the casing is adjacent to an area normally accessible when handling or cleaning, fit a partition 1 cm below the base of the casing with a 10x10 cm opening at the rear right-hand corner, to avoid any risk of burning or damage. There should also be a 5 cm gap between the appliance and all adjacent vertical surfaces. A foam adhesive is supplied with the hob. Stick this seal under the edge of the body as near as possible to the outer edge of the hob. Press round the edges of the hob, so that the seal flattens out and ensures an air tight seal. Warning : at the rear of the appliance, take care not to block the air inlets necessary for combustion to take place. FITTING THE SEAL · Top view of the seal SEAL · Cross section of the hob Worktop level seal 6 mm - Take care not to block the air inlets necessary for combustion to take place - 8 INSTALLATION: "BUILDING-IN" The body of the hob is fitted with 4 location holes to take the fixing brackets that secure the hob in the unit. Place the 4 fixing brackets in such a way that the hob is placed perfectly in the support unit. Location for fixing brackets Fixing bracket Building-in according to TYPE X (Norm CEI 335-2-6) Opening 10x10 cm 9 INSTALLATION: "GAS CONNECTION" The hob can be built-in ; it is type "X" for built-in hob (in compliance with electrical regulations EN 60. 335. 2. 6) ; in class 3 (in compliance with gas norm EN 30. 1. 1) ; adjoining furniture should not be higher than the level of the hob. This appliance is not connected to an evacuation device for the products of combustion. It must be installed and connected in compliance with the norms in force in the country of installation. Particular attention should be given to the availability of ventilation. The turnover of air necessary for combustion is a minimum of 2 m3/h per kW of power. Gas connection should be carried out in compliance with the norms in force in the country of installation. A stop tap, a regulator valve or a release valve for propane gas, should be fitted to the gas supply pipe. Use only taps, regulator valves, connectors and flexible hoses with the official mark of approval of the country of installation. CONNECT DIRECTLY TO THE THREADED END OF THE INLET PIPE ISO 7-1. 10 INSTALLATION: "ELECTRICAL CONNECTION" CONNECTION" The mains electricity supply connected to the appliance should comply with the norms in force in the country of installation. Connection to the mains electricity supply should be through a socket with an earth terminal, or through an intermediary switching device with a gap between contacts of at least 3 mm. [. . . ] The enamelled steel burner cap : do not immerse it in cold water when it is hot, this will prevent the enamel cracking as a result of thermal shock. · The burner body : regular cleaning will maintain the appliance original appearance. Clean with a soapy sponge, rinse and dry. If the holes become clogged, brush the caps using soapy water and dry with a clean cloth. [. . . ]