User manual CANDY PG640X

[. . . ] When there is an accessible space between the built-in hob and the cavity below, a dividing wall made of insulating material should be inserted (wood or a similar material). The wall should be at least 10 mm away from bottom of the drawer. 3) Important - The diagram below shows how the sealant should be applied. 4 gas ­ PL03/PL04 - / yes -/1 1/1 2 1 1 8, 95 kW 649 g/h 3 230V/50Hz yes 590x510 mm. IE cat. II2H3 + A B The Hob unit is fitted by attaching the Fixing Clamps supplied, using the holes at the base of the unit. Fig. [. . . ] If the power supply cord is damaged this is to be replaced by a qualified engineer so as to prevent any potential risk. The earth wire ( green a yellow coloured) must be at least 10 mm longer than the live and neutral wires. The section of the cable used must be of the correct size in relation to the absorbed power of the hob. Please check rating plate for the power details and ensure that the power supply cord is of the TYPE H05V2V2F. To prevent any potential damage to the hob please carry out the installation following this sequence: GB IE 1/2 GAS CONICAL A) As illustrated, assemble parts in sequence: A) fixed pipe B) washer C) Elbow fitting with tapered thred connection 2) Tighten the joints with the Spanners, remembering to twist the pipes into position. 3) Attach fitting C to mains gas supply using rigid copper pipe or flexible steel pipe. MAINS SUPPLY LIVE EARTH L BROWN WIRE GREEN/YELLOW WIRE BLUE WIRE POWER CABLE NEUTRAL N Please note Some models are equipped with both conical and cylindrical connectors for gas supply. Please select the type which is correct for the supply concerned. Fig. 5 GAS CONNECTION These instructions are for Fitters qualified for installation of equipment in line with the relevant national standard. All work must be carried out with the electricity supply disconnected. The rating plate on the hob shows the type of gas with which it is designed to be used. It is possible to use other types of gas after carrying out some simple modifications. (See the instructions in the following paragraphs). connection to the mains gas supply or gas cylinder should be carried out according to the relevant national standards, after having checked that it is regulated for the type of gas with which it will be supplied. If it is not correctly regulated follow the instructions in the paragraph entitlet «Adaption for different types of gas». For liquid gas (cylinder gas) use pressure regulators which comply with the relevant national standards. N. B. : for safe operation, economic use of energy and to ensure greater durability of the appliance, make sure that the supply pressure conforms with the values shown in the table on page 37. Use only pipes, washers and sealing washers which comply with the relevant national standards. When connecting the hob to the gas supply via use of flexible hoses please ensure that the maximum distance covered by the hose does not exceed 2 metres. N. B. : carry out a final check for leaks on the pipework using a soapy solution. Also, make sure that the flexible pipe cannot come into contact with a movlng part of the cabinet (eg, a drawer) and that it is not situated where it could be damaged. GB IE A Cylindrical (but connector) B Tapered thread conical ADAPTING THE HOB TO DIFFERENT TYPES OF GAS To adapt the Hob for use with different types of gas, carry out the following instructions: -- remove the grids and burners -- insert the hexagonal spanner (supplied) into the burner support (Fig. 6) -- unscrew the injector and replace it with one suitable for the gas to be used (see Table of gas consumption) -- carry out regulation of the burner. Hexagonal spanner Fig. 6 35 36 IE GB Table of gas consumption G20/G25 G30 G31 G20 20mbar G30 29mbar G31 37mbar 1W = 0, 860 kcal/h G25 Quota «X» depending on type of gas G20 G30 G25 G31 When you have carried out the new gas regulation, replace the old gas rating plate on your appliance with one (supplied with hob) suitable for the type of gas for which it has been regulated. Working burner large medium double ring maxi Ø injector Ø injector 1/100 mm 1/100 mm 120 80 93 61 2x94 2x65 2x94 2x65 Qn kW 2, 65 1, 5 3, 3 3, 3 l/h G20 252 143 314 314 g/h G30 193 109 238 238 g/h G31 189 107 236 236 Qn kW 2, 5 1, 45 3, 1 3, 1 l/h G25 277 161 343 343 Qmin. kW 0, 650 0, 380 0, 900 0, 900 air regul. [. . . ] In anycase from our after sales service centre the spare parts are available. A neon indicator light adjacent to the control knob will glow when the electric plate is in use. The additional electric hotplate/ring (ø 80 mm) where featured is turned on and off by pressing 0/I button, this hotplate has a fixed heat setting. Only pans which have smooth flat bases should be used on the electric hotplates. The size of the pan should be as close as possible to the diameter of the hotplate, and never smaller (see Fig. [. . . ]