User manual CANNON CANTERBURY FREESTANDING

[. . . ] Cannon CANTERBURY FREESTANDING MODELS USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS This heater is approved for use with Natural and Propane gases. Please leave instructions with the owner Contents Contents Warranty Distributor Safety warnings What to do if you smell gas Warnings Standards User instructions Operating instructions Flame characteristics Cleaning Heater specifications Installation instructions Clearances Installation Gas connection Log installation Gas control Gas pressure point Installation tips 16-17 9 10-15 6-8 4-5 2 3 Flue installation - Standard flue kit Flue kit Alternative double skin flue installation Alternative flue kit Service instructions 2 18-19 20-21 General Access to components To replace primary glass To replace the gas control To replace the fan To replace the electronic controller To remove the burner and electrodes 22-23 Trouble shooting Connections Wiring diagram Data label Date installed, Compliance Certificate No. For service to this appliance Warranty The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through the CANNON distributor. [. . . ] 23. The heater flames should be stable, not lifting from burner and the logs should glow after approximately 15 minutes operation on HIGH setting. The heater has been designed to burn with luminous flames, which mimic natural log combustion, and may exhibit slight carbon deposition. If heavy carbon deposits occurs or flames impinge on the roof of the combustion chamber, turn the appliance off and contact the service agent in your state. 24. If after following these installation instructions, and the trouble shooting chart on page 22-23, the heater does not perform correctly contact the our Technical Services Department. For contact details please refer page 24. 14 Installation tips Make sure that the heater is fully commissioned and be certain to test the integrity of the flue operation, taking into account any influences created by range-hoods, exhaust fans, central heating, etc. To avoid any unnecessary delays and inconveniences to your customer, please contact our Technical Services Department on 1300 727 421 if the installation is unusual or you have any concerns with the installation and/or heater operation before the installation commences. Any service request resulting from incorrect installations are not covered by our warranty conditions and these will result in charges, usually to the end user, so please be sure that the installation and commissioning has been satisfactorily carried out before calling for any warranty service. Please ensure that the end user is fully instructed on how to operate the heater. 15 Flue installation - Standard flue kit This heater is a flued appliance. It must be properly connected to a flue system in accordance with the latest edition of the Gas Installation Code, AS 5601. If elbows are required, we recommend 45° only and no more than two in the total flue run, there should also be a minimum of 250mm straight flue section in between bends. . If practical, locate the heater in a position to minimise the need for elbows. There must be at least 1. 8mm of vertical before any changes in direction of . 0 the flue. If placed against a combustible wall the 40mm rear spacers locate against the wall. Ensure clearances to combustible constructions have been observed. The centre line of the flue is 120mm to rear of appliance (including rear spacers). Carry out installation as per figure 25 (ceiling plate installation) and figure 26 (flue installation). Cut a hole 180mm ø in the ceiling in line with the flue position. Secure ceiling plate against the ceiling by bending out the tabs above the ceiling. Note: If the ceiling has an incline, the ceiling box will need to be fitted. The ceiling box is an accessory and can be ordered from the supplier. Installation instructions are supplied with the ceiling box. Part no: BOXB. 25 Flue kit The flue kit contains: 2 x 900mm lengths of 125mm ø painted upper flue. [. . . ] Continues to spark during flame presence. · Check that the wall socket to the appliance has correct polarity. Check polarity in the electrical supply lead to appliance. · Check that the sense electrode is in the flame. · Check that appliance is earthed correctly. [. . . ]