User manual CANON BJ-100 BROCHURE

[. . . ] Lotus 1-2-3 is a trademark of the Lotus Development Corporation. WordPerfect is a trademark of WordPerfect Corporation. Professional Write and PFS: First Choice are trademarks of Software Publishing Corporation. Multi Mate Advantage II is a trademark of Borland International, Inc. Chapter 1 Introduction How to Use This Manual This manual describes how to set up and operate the BJ-20, a portable printer from Canon. [. . . ] The buzzer sounds 3 times and the printer enters the print style setting mode. Press the PITCH switch the required number of times to move to the desired style. For example, to select 'Double-wide", press the switch 3 times. 3 4 Press the LF/FF switch to select the print style. The buzzer sounds a shorter beep, indicating the change is made. Press the ON LINE switch to exit the setting mode. The printer becomes online. Notes z "Printer reset" sets the print style to factory default (i. e. no print style). z The buzzer gives a beep for each step you make and sounds 2 times when you are back to "Current Setting". z To combine several print styles, e. g. "Emphasized" and "Double-wide", just use the PITCH switch to move to the desired style, and use the LF/FF switch to select it. To de-select a style: 1 2 3 4 Using Fonts Press the ON LINE and PITCH switches simultaneously. The buzzer sounds 3 times and the printer enters the print style setting mode. Press the PITCH switch the required number of times to move to the desired style. Press the LF/FF switch to dc-select the print style. In Lines ESC C n 27 67 n 1B 43 n In Inches ESC C 0 n 27 67 0 n 1B 43 00 n FORMAT DEC HEX Comment z The current line position becomes the top of page position. z Later changes in line spacing have no effect on page length. z This code releases the skip perforation settings, but does not change the vertical tab settings. z If the printer is in IBM Proprinter X24E emulation with the auto sheet feeder installed, page length setting becomes effective after the current page is ejected. The exceptions are: if the current page is at the top of page position, or if the present line number is smaller than the page length setting, then the page is not ejected, and the current line position taken as the top of page. z If the printer is in the Canon BJ-100e emulation, then regardless of the auto sheet feeder, the new page length setting becomes effective immediately, and the current position is taken as the top of page. Select/Cancel Emphasized Mode Select or cancel printing in twice the normal dot density. Select ESC E 27 69 1B 45 Cancel ESC F 27 70 1B 46 FORMAT DEC HEX Comment This mode overrides the condensed (17 cpi) mode. When the ESC E is entered in 17 cpi mode, the printer is set to the emphasized 10 cpi mode. Set Print Mode Set font and character pitch. FORMAT DEC HEX Comment n 0 2 3 4 6 7 8 10 12 Font and Pitch Draft 10 cpi (default) Letter Quality 10 cpi Letter Quality Proportional Down-Load Draft 10 cpi Down-Load Letter Quality 10 cpi Down-Load Letter Quality Proportional Draft 12 cpi (created from Draft 10 cpi) Letter Quality Prestige 12 cpi (or Letter Quality 12 cpi in Canon BJ-100e emulation) Down-Load Draft 12 cpi (created from down-Load Draft 12 cpi) ESC I n 27 73 n 1B 49 n 14 Down-Load Letter Quality 12 cpi 16 Down-Load Draft 17cpi (created from Draft 10 cpi) 18 Letter Quality 17 cpi 20 Draft 17 cpi (created from Down-Load Draft 10 cpi) 22 Down-Load Letter Quality 17 cpi (created from Down-Load Letter Quality 10 cpi Else Command ignored z The Internal fonts are used if the characters are not downloaded. z Set the DIP switch 10 to ON to enable down load. Select Sub-Sup Script Mode Select or cancel printing of characters in the tip (superscript) or bottom (subscript) area of the line. For subscript mode: FORMAT DEC HEX For superscript mode: Select ESC S 1 27 83 1 1B 53 01 Cancel ESC T 27 84 1B 54 FORMAT DEC HEX Select ESC S 0 27 83 0 1B 53 00 Cancel ESC T 27 84 1B 54 Select/Cancel Double Wide Mode Select or cancel printing of characters with character width double the normal size. Select ESC W 1 27 87 1 1B 57 0l Cancel ESC W 0 27 87 0 1B 57 00 FORMAT DEC HEX Set Presentation Highlight Set or cancel the presentation highlight (double-high) mode. [. . . ] Lotus 1-2-3 Setup String (Three-Digit Example) Any control codes you enter when using Lotus 1-2-3 will affect the entire spreadsheet. To enter a control code, first access the printer option setup menu by typing/PPOS. Then type each number in the code preceded by a backlash. Each number in the decimal form of the code must be three characters long, so you need to add a leading 0 if the code is a two-digit number. [. . . ]