User manual CANON BLACK & WHITE RANGE BROCHURE BROCHURE

[. . . ] If anything is missing or is damaged, contact your Canon Authorised Dealer or Sales Representative. Printer Setup Software & User's Guide CD-ROM Quick Start Guide Print Head 2 Ink Tanks * A USB cable should be purchased separately according to your computer. For details on cable specifications, refer to page 3. II Introduction IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIIIIIII This Quick Start Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. Instructions that, if ignored, could result in death or serious personal injury caused by incorrect operation of the equipment. [. . . ] · Always push the plug all the way into the power outlet. · Install only the print head packed in the printer package. Do not install any other print head in any case. It will never work. I Installing the Print Head ON 1 Plug the printer in. Do NOT turn on the computer yet. The POWER lamp flashes and the printer begins to operate. Wait until the POWER lamp remains fully lit. 3 Open the front cover. The print head holder moves to the centre. print head holder 4 Raise the lock lever. Do not touch the inside of the printer other than the lock lever. 4 5 Remove the protective cap from the print head. Notes print head print head protective cap nozzles · Do not touch the print head nozzles or electrical contacts. · Do not attempt to reattach the protective cap once it has been removed. electrical contacts 6 Place the print head in the holder. 7 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed. I Installing the Ink Tanks · For safety reasons, store ink tanks out of the reach of small children. · Do not drop or shake ink tanks. 1 Take out the black ink tank. 5 protective cap 2 Hold the ink tank as shown in the diagram and remove the protective cap. Notes · Do not shake or drop ink tanks as this may cause the ink to leak out and stain your clothes and hands. · Do not attempt to reattach the protective cap once it has been removed. ink port 3 Insert the black ink tank into the righthand slot. 4 Press the top until it clicks into place. 5 Use the same procedure to install the colour ink tank in the left hand slot. 6 Close the front cover. Wait until the POWER lamp remains fully lit (about 60 seconds). Note You will be notified by the low ink warning when ink is low during printing. For more details about the low ink warning, refer to the User's Guide. 6 II 4 I Loading Paper IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIIIIIII I Loading A4 (Letter) Size Plain Paper paper thickness lever 1 Open the front cover. 2 Move the paper thickness lever at the top of the print head holder to the left position. The printer is now ready to use. 13 I Aligning the Print Head - Macintosh 1 Select Page Setup in the File Menu. 2 Click Utilities. 3 Select Test Print from the menu and click the Print Head Alignment icon. 4 Check that paper is loaded in the printer and click OK. If the pattern is not printed successfully, open the front cover and ensure that the ink tanks are correctly installed. 5 Look at the print-out. From the patterns in Column A, select the most even, least irregular pattern and enter the number. 14 6 In the same way, one by one, select the most even patterns printed with the least irregularities from each of Columns B to F, enter their numbers and click Send. If it is difficult to pick the best pattern on Column F, pick the setting that produces the least noticeable vertical white stripes. Less noticeable white stripes More noticeable white stripes 7 Click Close. 8 Click OK. This completes the printer setup. · Use the application to set the paper size and paper orientation. Before printing, open the settings screen and check that the Page Size in the Page Setup tab is the same as that specified within application. · Refer to the User's Guide for more information about printer driver functionality. 17 II Printing with Macintosh IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIIII Adjusting the print settings according to your needs allows you to produce better quality prints. I Printing 1 Open the Page Setup dialog box in your application. On the File menu, click Page Setup. Check the application's users manual for the actual procedures. 2 Specify the page setup. For details, refer to "Page Setup" on page 19. 3 Open the Print dialog box in your application to print the document. On the File menu, click Print. Check the application's users manual for the actual procedures. 4 Specify the print settings according to your requirements. For details, refer to "Basic Print Settings" on page 19. 5 Click the Print button. Printing will start in a few moments. 18 I Page Setup Use the Page Setup dialog box to specify the paper size settings. Select paper size you wish to use. I Basic Print Settings For the best print quality, specify the minimum requirement settings in the Print dialog box. To get the best results, ensure you select the type of media loaded in the printer when printing on paper other than plain paper. (3) (1) (2) (1) Media Type (2) Print Mode Select the type of media loaded in the printer. Select the type of document you want to print. To specify more detailed settings for the print quality or colour, select Manual and click Details. [. . . ] is displayed, click OK. 3 When the Terminate Installation screen 4 Turn the printer off. 5 Reinstall the printer driver (see page 8). For Further Details. . . For more information, place the Setup Software & User's Guide CD-ROM in the CD-ROM drive. I User's Guide Contents The "User's Guide" is in PDF format and can be found on the same CD-ROM as the printer driver. You can view this Guide on screen and print out any sections you require. Contents · Printer parts and their functions · Printer driver functions · Routine maintenance · Printing media · Troubleshooting · Specifications I How to View the User's Guide For Windows (1) Load the CD-ROM in your computer. [. . . ]