User manual CANON EOS REBEL X/XS EOS REBEL XS INSTRUCTION MANUAL

[. . . ] In consideration of the right to use the SOFTWARE, you agree to abide by the terms and conditions of this Agreement. LICENSE: Canon grants you the non-exclusive right to use the SOFTWARE only on a single computer. You may physically transfer the SOFTWARE from one computer to another provided that the SOFTWARE is used on only one computer at a time. You shall not install or use the SOFTWARE on a network, multiple CPU, multiple site arrangement, or any other hardware configuration where the SOFTWARE is accessible to more than one CPU or to more than one user. [. . . ] To exit the TWAIN Driver, select the [File] menu [Exit]. 4 Select the image to be transferred and select the [File] menu [Transfer Images]. The image transferred to Photoshop is displayed. You cannot display or download the images saved on an SD card. You can also transfer images by double-clicking a thumbnail image. The method for starting the application and the dialog box contents differ depending on your retouching software. Refer to the retouching software User's Manual for details. W-102 Troubleshooting and Uninstallation W This chapter provides troubleshooting and describes the software uninstallation procedures. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-104 Uninstalling the Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-108 Uninstalling the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-108 Uninstalling the Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-109 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W-117 7 Troubleshooting When the "Could not complete installation correctly" or "Communication between the camera and computer failed" message appears, check the items described below. The camera name is shown in the operation screens as "EOS XXX". Installation failed. If you are using Windows XP Professional or Windows 2000, are you using the computer under a user setting other than [Computer administrator] or [Administrator]? You cannot install software if a user setting other than [Computer administrator] or [Administrator] is selected. Select the [Computer administrator] user setting in Windows XP Professional or the [Administrator] user setting in Windows 2000. For detailed information on selecting the user setting, refer to the computer User's Manual. Is the cable firmly plugged into its socket? To complete the installation, ensure that the plugs on the dedicated cable are securely plugged into the ports on the camera and computer when you connect the camera to your computer (W-8). Are the camera and computer set up correctly for communication? Is the camera's power switch set to <ON>?1 Delete the camera or [Canon Digital Camera] displayed in [Other devices] or [Unknown devices]. 2 Disconnect the dedicated cable and delete the driver (W-109). 3 Re-install the driver (W-4). I connected the camera to the computer before installing the software Did you set the camera's power switch to <ON>? If you did not set the camera's power switch to <ON>, proceed as follows: 1 Disconnect the dedicated cable from the camera and computer. 2 Install the Solution Disk software on your computer using the correct installation procedure (W-4) and then connect the camera to your computer to complete the installation (W-8). If you set the camera's power switch to <ON>, proceed as follows: 1 If [Found New Hardware Wizard] or any other dialog boxes appear, click the [Cancel] buttons to cancel all the dialog boxes. 2 Set the camera's power switch to <OFF>. 3 Disconnect the dedicated cable from the camera and computer. 4 Install the Solution Disk software on your computer using the correct installation procedure (W-4) and then connect the camera to your computer to complete the installation (W-8). W To Display the Device Manager Windows XP Troubleshooting and Uninstallation Click the [Start] button select [Control Panel] [Performance and Maintenance] [See basic information about your computer]. Then select the [Hardware] tab and click the [Device Manager] button. 7 Windows 2000 Click the [Start] button select [Settings] [Control Panel]. Then double-click the [System] icon to open and select the [Hardware] tab and click the [Device Manager] button. Windows Me and Windows 98 SE Click the [Start] button select [Settings] [Control Panel]. Then double-click the [System] icon to open and select the [Device Manager] tab. W-107 Uninstalling the Software Before beginning the software uninstallation, exit all programs you are using and disconnect the dedicated cable from your computer. Uninstalling the Software The following uses the procedures for uninstalling EOS Viewer Utility as an example for uninstalling other programs as well. [. . . ] M-30 Specifying the Processing Parameters (EOS Capture) . M-96 Specifying the Save Destination (EOS Capture) M-93 Specifying the Tone Curve . . . . . . . . . . . . . . . . . . . . M-80 Starting EOS Viewer Utility . . . . . . . . . . . . . . . . . . . M-12 Starting the Remote Shooting Function . . . . M-88 Supported Image Formats . . . . . . . . . . . . . . . . . . . . [. . . ]