User manual CANON EOS 1D MARK II

[. . . ] Windows Macintosh Software Instruction Manual E INSTRUCTION MANUAL READ CAREFULLY BEFORE USING! CANON SOFTWARE LICENSE AGREEMENT IMPORTANT - READ THIS AGREEMENT BEFORE USING THE SOFTWARE ON THE CDROM IN THIS BOX. BY USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE TERMS OF THIS AGREEMENT. This is a license agreement (the [Agreement]) between you and Canon Inc. IF YOU DO NOT AGREE TO THE TERMS AND CONDITIONS OF THIS AGREEMENT, DO NOT USE THE SOFTWARE PROGRAM ON THE CD-ROM AND THE USER MANUAL IN THIS BOX (COLLECTIVELY, THE [SOFTWARE]) AND RETURN THE SOFTWARE WITHIN 30 DAYS FROM THE DATE OF PURCHASE TO YOUR POINT OF PURCHASE FOR A REFUND. [. . . ] Even when the camera's power switch is set to <ON>, operation of the Auto power off function will automatically switch the camera off. To prevent this, set the Auto power off function to [Off]. (Refer to "Menu Operations" in the camera's Instruction Manual. ) Does the [Add New Hardware Wizard] ([Found New Hardware Wizard] in Windows 2000) dialog box appear during installation? Click the [Cancel] button, disconnect the dedicated cable, and then repeat the installation procedure from the beginning. Doesn't the installer panel appear? Use the following procedure to display the installer panel. (In other versions of Windows, double-click [My Computer] on the desktop. ) rightclick the CD-ROM drive containing the CD select [Open] from the menu that appears double-click the icon on the right. W-104 Troubleshooting I have installed the software but the camera and computer cannot communicate. Is the driver installed? The driver is required for communications between the camera and computer. When you want to communicate between the camera and computer, be sure to install the driver shown below appropriate to your windows. · Windows XP/Windows Me: WIA Driver · Windows 2000/Windows 98 SE: TWAIN Driver W Have you installed the WIA Driver or TWAIN Driver? Even if you have installed the WIA Driver or TWAIN Driver, installation is not completed unless the camera is connected to the computer. Insert the Solution Disk into the CDROM drive, install the WIA Driver or TWAIN Driver, and then connect the camera to your computer. Does your computer comply with these requirements? PC with Windows XP, Windows 2000, Windows Me or Windows 98 SE preinstalled and equipped with an IEEE1394 port (W-2). * Operation is not guaranteed when an IEEE1394 connection is used on computer systems other than those listed above. Are the camera and computer connected correctly? Connect the camera to your computer correctly using the dedicated cable (W-8). Is there sufficient charge left in the camera battery? Your computer does not supply power to the camera. Connect the DC Coupler Kit to the camera or load a fully charged battery into the camera before connecting it to your computer. Do you have more than one camera connected to your computer? Troubleshooting and Uninstallation If you connect more than one camera to the same computer, the driver and camera may not operate normally. Exit the software and disconnect all the dedicated cables. Then connect only one camera to the same computer again. 7 W-105 Troubleshooting Is the driver operating normally? Connect the camera to your computer with the dedicated cable and set the camera's power switch to <ON> (W-8) and open [Device Manager] (W-107). Click the plus symbol [+] to the left of [Imaging devices] and check that the connected camera is displayed. If the connected camera is not displayed, the driver is not operating normally. Briefly disconnect and then reconnect the dedicated cable, ensuring that the connection is secure. If the connected camera still does not appear, use the following procedure to reinstall the driver. 1 Disconnect the dedicated cable and delete the driver (W-109). When the [X], [!] or [?] symbol is displayed beside the connected camera, part of the driver is missing or corrupted. Use the following procedure to re-install the driver. 1 Delete the camera displayed in [Imaging devices]. 2 Disconnect the dedicated cable and delete the driver (W-109). 3 Re-install the driver (W-4). Is the driver installed correctly? Connect the camera to your computer with the dedicated cable and set the camera's power switch to <ON> (W-8) and open [Device Manager] (W-107). Click the plus symbol [+] to the left of [Other devices] or [Unknown devices] and check whether the connected camera or [Canon Digital Camera] is displayed. W-106 Troubleshooting If the connected camera or [Canon Digital Camera] is displayed in [Other devices] or [Unknown devices], the driver was not installed correctly. Use the following procedure to re-install the driver. [. . . ] M-17 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M-2 T Thumbnail Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M-20 Tone Curve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . M-40 Transferring Images to Retouching Software . . M-48 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]