User manual CANON ES410V BROCHURE

[. . . ] ●● ●● Menu button When you receive mainly faxes and sometimes voice calls:
Select FAX priority mode. When you have a dedicated telephone line for fax use only:
Select FAX only mode. When you receive mainly voice calls and sometimes faxes:
Select TEL priority mode. When you subscribe to a ring pattern detection service provided by your telephone company, and you want to receive a fax only if the machine detects the pattern for fax:
Select DRPD (Dictinctive Ring Pattern Detection). 1 Press the FAX button 2 Press the Menu button FAX button ●● ●● 5 When the FAX menu returns, press the Back button For details on fax settings and how to change them, refer to the on-screen manual: Basic Guide. 14 Set Up Your Fax Sender Information For details on sender information, refer to "Specifying the Basic Settings for the Machine" in the on-screen manual: Basic Guide. [. . . ] The serial number is located on the product packaging and on the inside of the product. Connecting to a Network Go to "Connect to Your Network (optional)" on page 18 If you plan to connect to a network but select USB connection by mistake you will need to reinstall the software. Connecting with a USB Cable After your computer restarts, the Canon IJ Network Tool dialog appears. 8 Click Restart After restarting, remove the Setup CD-ROM and keep it in a safe place. 1 Select USB connection Only select USB connection if you plan to connect the MX860 directly to a single computer and not to a network. if you plan to connect directly to one computer only by USB, leave the default option as is 2 Click OK Congratulations!You are finished with the setup. Go to "Start Using Your MX860!" on page 37. Decide how you want to connect to your MX860. prepare prepare prepare prepare hardware hardware hardware hardware software software software software network network network network 17 Connect to Your Network (optional) Choose Your Network Type wireless network with a single access point wireless network with multiple access points wired network connecting with an Ethernet cable (example: Airport Extreme and Airport Express) Wi-Fi router Wi-Fi router router Wi-Fi router Go to page 19. Go to page 23. Go to page 28. The MX860 can not be used over a wireless network and a wired network at the same time. To connect additional computers to the MX860, go to "Connecting Additional Computers" on page 33. 18 wireless network with a single access point Wireless Networks with a Single Access Point wireless network with multiple access points (example: Airport Extreme and Airport Express) 3 Select LAN connection wired network connecting with an Ethernet cable On the Canon IJ Network Tool dialog, select LAN connection, then click OK. Wi-Fi router Wi-Fi router router Wi-Fi router 4 Select printer to use a Select Setup in the pop-up menu. b Select MX860 series in the Printers pane, then click OK. If your network has more than one wireless access point, go to page 23. 1 Locate the name and password (if applicable) of your wireless network Click the icon in the menu bar and write down the network name with the checkmark next to it. 2 Make sure the MX860 is ready Ensure the MX860 is connected to your computer with the USB cable and is powered on. You will need the USB cable only for the initial network setup. Once your MX860 is connected to your network, the USB cable is no longer needed. The MX860 is set at the factory to connect to a wireless (Wi-Fi) network. If your MX860 was previously set for a wired network, set the connection type now for a wireless network. See "Set the Network Connection Type" on page 28 for details. prepare prepare prepare prepare hardware hardware hardware hardware software software software software network network network network 19 5 Select your wireless network a c Select the network name you wrote down in step 1. b On your computer, click Next. b If your network requires a password, enter it. Click Connect. The network password is case sensitive. If the MX860 does not connect, see section 5. 6 of the printed manual "Network Setup Troubleshooting. " Measuring Wireless Connection Performance 1 Click Next. 6 Complete the network setup When the Setup Completion dialog appears: a Disconnect the USB cable and place the MX860 where it will be used. The connection measurement results will display. 20 2 Review results a b If you see a green check mark and the word Good, click Finish. Click Add. 32 Select the Scanner The Canon IJ Network Scanner Selector dialog opens. Connecting Additional Computers More than one networked computer can print to your MX860. Follow the instructions in this section if one computer has already been setup to use your MX860 on a network. (See "Connect to Your Network (optional)" on page 18. ) A USB cable is not required for connecting additional networked computers to your MX860. 1 Make sure the MX860 is on and connected to your wireless or wired network a 2 Install the software on the additional computer 1 Select scanner a From the pop-up menu, select Canon MX860 series Network. There should be only one device listed unless you have more than one MX860 series device connected to your network. Follow the software installation steps in "Set Up the Software" on page 15. IJ Network Tool automatically starts. b In the Network Device List pane, select the MAC address of the b After installing the software and restarting your computer, the Canon 3 Select LAN connection On the Canon IJ Network Tool dialog, select LAN connection, then click OK. c Click Apply to use the MX860 as a scanner. click Exit. d Confirm that a checkmark appears next to the selected device, then Congratulations!You are finished with the setup. Go to "Start Using Your MX860!" on page 37. prepare prepare prepare prepare hardware hardware hardware hardware software software software software network network network network 33 4 If the Setup Preparations screen appears, confirm that preparation is complete, then click OK. Add the Printer (OS X v10. 5. x) The Printer Browser window will open automatically. 1 Select the printer a b Click More Printers. Click Add. 5 Register printer a b Select Setup in the pop-up menu. Click Register Printer. c 6 Click Cancel When the Cancel Setup screen appears, click Cancel, or if the You have no printers available screen appears, click Cancel. The letters and numbers after "MX860 series" show the MAC address for this device (Media Access Control address, a unique identifier for any equipment connected to a network). 34 Add the Printer (OS X v10. 4. x) The Printer List window will open automatically. Add the Printer (OS X v10. 3. 9) The Printer List window will open automatically. 1 Click Add 1 Click Add 2 Add the printer a b c Click More Printers. Click Add. 2 The Printer Browser window opens. a b Select MX860 series. [. . . ] Click Add. prepare prepare prepare prepare hardware hardware hardware hardware software software software software network network network network 35 Select the Scanner The Canon IJ Network Scanner Selector dialog opens. 1 Select scanner a From the pop-up menu, select Canon MX860 series Network. There should be only one device listed unless you have more than one MX860 series device connected to your network. b In the Network Device List pane, select the MAC address of the c Click Apply to use the MX860 as a scanner. click Exit. d Confirm that a checkmark appears next to the selected device, then Congratulations!You are finished with the setup. Go to "Start Using Your MX860!" on page 37. 36 Start Using Your MX860! Solution Menu The Solution Menu provides quick access to useful functions and information about your MX860. [. . . ]