User manual CANON ES90 BROCHURE

[. . . ] The Hardware section provides general information about the scanner operational settings, maintenance, and troubleshooting. The Software section describes how to use the ISIS/ TWAIN driver with the scanner, and how to set up job registration tools. CapturePerfect 3. 0 Operation Guide (Electronic Manual) This is the operation guide for CapturePerfect 3. 0, the Canon document scanner application program. ❏ Installing the Securing Braces The securing brace prevents the scanner from tipping backward when the feeder is open. Make sure to install the securing plates before using the scanner. 9. ❏ Close all other applications before installing the software. Click [Next]. 1. [. . . ] The setup menu consists of the following screens: Menu Screen Typical Installation 12. Click [Finish] to complete the installation of CapturePerfect 3. 0. Next, the installation wizard for the User Manual appears. Checking the Package Contents When you unpack your scanner, make sure all of the following accessories are included. If any of the items listed below are missing or damaged, contact your local authorized Canon dealer or service representative. After checking the package contents, you need to install the software. (☞ STEP 2) * Installs all of the software displayed. 13. Click [Next]. Installation of the User Manual starts. Read Manuals Custom Installation Installing the Software Install the software before connecting the scanner to the computer. DR-7090C Securing braces (2) Screws (4) Power Cord (Length: 1. 5 m) USB Cable (Length: 2 m) CAUTION ❏ Before installing the software, make sure your computer is correctly running one of the following versions of Windows. For details on system requirements, refer to “Installation Requirements” on p. • Windows 2000 Professional SP4 or later • Windows XP Home Edition SP3 or later • Windows XP Professional SP3 or later • Windows XP Professional x64 Edition SP2 or later • Windows Vista Home Basic/Home Premium/Business/Ultimate/Enterprise (32- and 64-bit versions) SP1 or later ❏ Do not connect the scanner to the computer before installing the software. If you connect the scanner and turn it ON before you install the software, a wizard screen will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF. Windows 2000 * The User Manual and CapturePerfect 3. 0 Operation Guide electronic manuals for the scanner are installed on the computer with the rest of the software. * Installs only the selected software. 14. Select the method that is best suited to your computer environment. CAUTION ❏ Observe the following when connecting the scanner with other devices in a “daisy chain”. • The SCSI ID of the scanner is set to “SCSI ID = 2” by default. When using a daisy-chain configuration with other SCSI devices, set the DIP switches so that SCSI ID numbers are not duplicated in the system. DIP switches (SW1 to SW3 = SCSI ID, SW4 = Terminator) IMPORTANT ● With Windows Vista, installation proceeds automatically regardless of the displayed “Check here for status” balloon help. You can click “Check here for status” to display the installation progress. Selecting the Scanner To use the scanner with an ISIS/TWAIN-compliant application program, the scanner must first be selected. The menus and procedures used for selecting scanners vary depending on the application used. For detailed information on selecting scanners, refer to the user’s manual for your application. This section describes how to select the scanner when using CapturePerfect 3. 0. For details on how to use CapturePerfect 3. 0, refer to CapturePerfect 3. 0 Operation Guide located in the Windows program menu. SCSI Connector (D-sub, 50-pin half-pitch) ● With Windows XP and Vista, a message appears when installation is finished. Windows XP 1. USB Connector OFF ON SCSI ID 0 SW1 OFF ON OFF ON OFF ON OFF ON SW2 OFF OFF ON ON OFF OFF ON ON SW3 OFF OFF OFF OFF ON ON ON ON Launch CapturePerfect 3. 0 from the Windows program menu. 1 2 3 4 DIP Switches for SCSI ID Power Connector 1 2 3 4 5 6 7 Windows Vista CAUTION ❏ ❏ ❏ ❏ Do not connect both USB and SCSI cables to the scanner at the same time. The scanner and computer should both be turned OFF when making connections. Make sure that the computer is turned OFF before connecting the SCSI cable. [. . . ] Next, you need to select the scanner from your application program. (☞ STEP 5) Select [CANON DR-7090C], and click [Settings]. Connecting the Power Cord 1. Connect the supplied power cord into the power connector on the back of the 1 scanner. (1) The [Configure Device Settings] dialog box appears. 4. Set the default page size. 2. Connect the power cord into an AC outlet. [. . . ]