User manual CANON IMAGECLASS D1170 DATASHEET

[. . . ] The “Hardware” volume explains all topics related to handling and caring for the scanner (i. e. , setup, cleaning, maintenance, and troubleshooting. ) The “Software” volume explains the ISIS/TWAIN driver settings and Job Registration Tool settings. CapturePerfect 3. 0 Operation Guide (electronic manual) Explains the application that enhances the operation of all Canon document scanners. 2. Carefully open the document feed tray and protective sheet. Document Feed Tray 3. Load the retard roller so that its notch aligns with the shaft on the scanner. Read Manuals * Installs all of the software displayed. Custom Installation 3. Peel off the orange tape from all the places marked below. 4. Slide the lock lever to the left so that its shaft fits into the retard roller (1), and then flip the lock lever completely down to lock the retard roller (2). * The User Manual and CapturePerfect 3. 0 Operation Guide electronic manuals for the scanner are installed on the computer with the rest of the software. [. . . ] Load the roller unit so that its notch aligns with the shaft pin on the scanner. Easy Start Guide (This Manual) Reference Guide DR-6010C Setup Disc Adobe Acrobat Setup Disc Install the software before connecting the scanner to the computer. The Job Tool is installed after the scanner driver. Warning ❏ Before installing the software, make sure your computer is correctly running one of the following versions of Windows. For details, refer to the Reference Guide. • Microsoft Windows 2000 Professional SP4 or later • Microsoft Windows XP Professional SP3 or later • Microsoft Windows XP Home Edition SP3 or later • Microsoft Windows XP Professional x64 Edition SP2 or later • Microsoft Windows Vista Home basic, Home Premium, Business, Ultimate or Enterprise SP1 or later ❏ Do not connect the scanner to the computer before installing the software. If you connect the scanner and turn it ON before you install the software, a wizard screen will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn the scanner OFF. Warranty Card Registration Card Retard Roller Roller Unit 3. Slide the lock lever to the left (1), and then lift the roller unit into place (2). Note Items included in this package are subject to change without notice. ● Keep the package and packing materials for storing or transporting the scanner. ● 7. Click [Finish] to complete the installation. Next, the installation wizard for CapturePerfect 3. 0 appears. 4. Flip the lock lever up to lock the roller unit. After checking the package contents, you need to remove all the packing materials protecting the scanner. (☞ STEP 2) ■ Trademarks • Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be trademarks or registered trademarks in other countries. Next, you need to turn on the scanner and ensure Windows recognizes it. (☞ STEP 5) 3. Load your document in the document feed tray with the printed side facing up, and adjust the document guides to the width of the document. Document Guides Turning the Power ON (Scanner Recognition) When you turn ON the DR-6010C after connecting it to your computer, Windows uses the Plug and Play feature to recognize the scanner and automatically installs the necessary driver. 4. Warning Make sure the feed selection lever is set to the bottom position (page separation). Be careful not to set the feed selection lever to the top position (bypass) because this will cause the document pages to feed as a stack, rather than separately. For details on the feed selection lever, refer to the User Manual. 4. Connect the scanner to your computer with the supplied USB cable. Type A ❏ When the scanner is connected by a SCSI cable, always turn ON the scanner before the computer. Turning ON the computer first may prevent it from recognizing the scanner properly. ❏ Be sure to log on with Administrator privileges when logging on to Windows. ❏ Wait at least 10 seconds before turning the scanner ON again after turning it OFF. ❏ If the scanner will not be used for an extended period, be sure to unplug it from the power outlet for safety. Feed Selection Lever 5. Press the job button (3). Click [Finish] to complete the installation of the User Manual. Type B Insert the plug with the mark facing down. When Connecting by SCSI 1. Make sure your computer is turned OFF before connecting the SCSI cable. Make sure the scanner’s power switch is in the OFF position. [. . . ] 1 Plug the power cord into the power outlet (2). 2 (Windows Vista) 7. Click [Close] to close the DR-6010C monitor. Connecting the Scanner to Your PC The scanner can be connected to a computer in two ways: by USB connection to a standard USB port on the computer, or by SCSI connection to a SCSI card installed in one of the computer’s expansion slots. Select a connection method appropriate to your computing environment. SCSI ID Dip Switches (Windows 2000) Note ● ● (Windows XP) ● ● ● 5. Connect the scanner to your computer with the SCSI cable. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. Note ● In Windows Vista and Windows XP, a message appears when installation is complete. ● The following functions are assigned by default to the job buttons. [. . . ]