User manual CANON IMAGERUNNER 1730 BROCHURE

[. . . ] The following do not apply if they do not conform to the laws and regulations of the region where the manual or product is used: Trademarks Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders. Copyright All rights reserved. No parts of this manual may be reproduced in any form or by any means or translated into another language without the written permission of Canon Inc. , except in the case of internal business use. Copyright © 2005 by Canon Inc. 2 451, Tsukagoshi 3-chome, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8530, Japan I. MANUAL OUTLINE This manual consists of the following three parts to provide information necessary to service the PIXMA iP5200: Part 1: Maintenance Information on maintenance and troubleshooting of the PIXMA iP5200 Part 2: Technical Reference New technology and technical information such as FAQ's (Frequently Asked Questions) of the PIXMA iP5200 Part 3: Appendix Block diagrams and pin layouts of the PIXMA iP5200 Reference: This manual does not provide sufficient information for disassembly and reassembly procedures. [. . . ] 2) After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print operation (due to dislocation of the belt or gear, or out-of-phase motor, etc. ) occurs. Note: The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit. DO NOT loosen them in other cases. (2) Grease application 1) Printer unit 1-21 2) CL base / CL gear 1-22 3) PR shaft / LF roller bushing To the top <Part 1: 3. REPAIR, 3-3 (1) to (2)> 1-23 (3) Waste ink counter setting When the logic board ass'y is replaced, reset the waste ink counter. In addition, according to the waste ink amount, replace the waste ink absorber (ink absorber kit). The standard amount for waste ink absorber replacement is given in the table below. Waste ink amount*1 Less than 7% 7% or more Ink absorber kit replacement Not required. Required. *1: Check the waste ink amount by service test print or EEPROM information print. Adjustment / Settings, (5) Service mode, for details. ] (4) User mode Function Print head manual cleaning Procedures - Cleaning both black and color: See "Standalone printer operation" below. - Cleaning black or color separately, or both black and color: Perform from the printer driver Maintenance tab. Remarks Print head deep cleaning - Cleaning black or color separately, or both black and color: Perform from the printer driver Maintenance tab. Paper feed roller cleaning Nozzle check pattern printing See "Standalone printer operation" below. Green (Power) Power off 1 time 2 times 3 times 4 times 5 times Orange (Alarm) Service test print Green (Power) EEPROM information See 3-4. Verification Items, (2) EEPROM information print. print Orange (Alarm) EEPROM initialization Green (Power) Waste ink counter resetting Orange (Alarm) Destination settings After entering the destination settings mode, press the Resume/Cancel button the specified number of time(s) to select the destination. For detail, see "Destination settings procedures" below. (Cleaning of both black and color) 6 times 7 times 8 times 9 times Green (Power) Print head deep cleaning Orange (Alarm) LF correction Green (Power) CD / DVD check pattern print Orange (Alarm) CD / DVD print position correction (horizontal: X direction) Green (Power) CD / DVD print position correction (vertical: Y direction) Orange, Green, Return to the menu Orange selection (Alarm, Power, Alarm) Not used in servicing. Not used in servicing. 10 times Not used in servicing. 11 to 13 times 14 times Green (Power) Left margin correction Not used in servicing. 1-26 15 times Orange (Alarm) Return to the menu selection Note: If the Resume/Cancel button is pressed 16 or more times, the Alarm or Power LED lights steadily without any changes. <Destination settings procedures> In the destination settings mode, press the Resume/Cancel button the specified number of time(s) according to the destination listed in the table below, and press the Power button. Time(s) 0 times 1 time 2 times 3 times 4 times 5 times 6 times 7 times 8 times 9 times LED indication Destination CD / DVD print Green (Power) No change of the destination Orange (Alarm) Japan Green (Power) Korea Orange (Alarm) US Green (Power) Europe Orange (Alarm) Australia Green (Power) Asia Orange (Alarm) China Green (Power) Taiwan Orange (Alarm) Return to the Destination setting mode Supported Not supported Not supported Supported Supported Supported Supported Supported Note: After setting the destination, confirm the model name and destination in service test print or EEPROM information print. Verification Items, (1) Service test print, or (2) EEPROM information print. ] <LF correction procedures> Purpose: After replacement of the feed roller ass'y or logic board ass'y in repair servicing or in rebox operation, adjust the line feeding in the same way as done at the production site. Operation: Print the LF correction pattern, and select the Pattern No. from 0 to 2 which contains the least streaks or lines. Press theResume/Cancel button the same number of times as the selected Pattern No. , and press the Power button. [. . . ] Remarks 3. REPAIR 3. 1 Notes on Service Part Replacement (and Disassembling/Reassembling) Service part NIC BOARD ASS'Y (QK1-1973-000) Notes on replacement Adjustment/settings Operation check - Network setting information print - Printing with wireless LAN I/F (After printing, EEPROM initialization of NIC BOARD is necessary. ) 3 Note: If the NIC BOARD is replaced, user network setting information stored in the NIC BOARD is lost. Therefore, it is necessary to inform users that network setting should be performed again to enable the printer to be used under the user's environment. <How to re-perform network setting> a. Performing Easy Install Application software, User's Guide, etc, are also re-installed. [. . . ]