User manual CANON IMAGERUNNER 3570 MAC OS X V1.40 FAX GUIDE

[. . . ] Once inserted, fold the extension as shown . 4 Pinch and slide the rear paper end guide to match the size of paper. NOTE Confirm that the paper guide is fitted in the paper size slit correctly. To load Legal-size paper: Pull the blue tab and extend the cassette as far as it will go. Keep the rear paper end guide to LTR size mark. If you are not using Legal-size paper, skip to the next step without extending the cassette. A 5 Load the paper into the cassette. Make sure the paper stack sits below the hooks (A). 6 Pinch and slide the side paper end guides to match the size of paper. A B 7 Even out the edges of the paper stack. [. . . ] Make sure the paper stack sits below the hooks (A). 6 Pinch and slide the side paper end guides to match the size of paper. A B 7 Even out the edges of the paper stack. Make sure the height of the stack does not exceed the limit marks (A) and that the side edges of the stack are below the hooks (B). 8 Insert the paper cassette back into the machine as far as it will go. NOTE If you do not completely insert the cassette into the machine, paper jams may occur. IMPORTANT Do not push in the cassette at an angle. Doing so may damage the paper sensing lever inside the machine. 9 Insert the tabs on the extension cover into the slots on the back of the machine, and carefully lower the cover until it sits on the cassette extension beneath it. IMPORTANT Do not load paper from the back of the machine. Doing so may damage the paper feeding assembly inside the machine. Connect the telephone cable and any necessary external device. Connect the telephone cable to the wall jack. Connect external devices as follows: = Telephone line jack = External device jack Telephone or answering machine Telephone line Machine Telephone or answering machine Telephone and answering machine Telephone line Machine LINE TEL Answering machine Telephone You can connect an external device if necessary (optional). Built-in computer modem and telephone Telephone line Machine LINE TEL Computer Telephone Connect the power cord. 1 Plug the power cord into the rear socket . Then connect the other end to the wall outlet . 2 Once it is warmed up, the standby display appears in the LCD. IMPORTANT For important safety instructions on installation and handling of the machine, see "Important Safety Instructions" in the Basic Guide. NOTE Make sure the correct paper size is specified in the machine. For details, see Chapter 2, "Paper Handling, " in the Basic Guide. Set the receive mode Press [Menu]. Press [ (­)] or [ (+)] to select SCAN COPY FAX <FAX SETTINGS> press [Set] . 3 Press [ (­)] or [ (+)] to select <RECEIVE MODE> press [Set] . 4 Press [ (­)] or [ (+)] to select the Stop/Reset Start receive mode press [Set] . You can select from the following: <FaxOnly> to automatically receive faxes, all calls will be answered as fax transmission. You can also click [Read Manuals] on this screen to read PDF manuals. 6 Click [Install MF Drivers]. 7 When the MF Drivers-Setup Wizard screen appears, click [Yes] and follow the instructions on the screen. 8 When the installation is complete, click [Exit] to close the MF Drivers-Setup Wizard screen. 9 On the MF Setup screen, click [Install MF Toolbox]. 10 When the MF Toolbox-Setup Wizard screen appears, click [Next] and follow the instructions on the screen. NOTE Before installing MF Toolbox, make sure that all other applications are closed and that any anti-virus software on your computer is disabled. 11 When the installation is complete, click [Exit] to close the MF Toolbox-Setup Wizard screen. Connect the machine to your computer. 1 Make sure the machine's power is turned on. Connect the cable to the USB port on the back of the machine. Then connect the other end of the cable to the USB port on your computer. 2 After the installation is complete, click [Exit] to close the MF Setup screen. Remove the User Software CD from the CD-ROM drive and store it in a safe place. NOTE If you would like to install the optional Presto!PageManager file management software and/or OmniPage OCR software, click [Install Applications] and follow the instructions on the screen. You can also click [Read Manuals] to read PDF manuals in the User Software CD. To view the manuals in PDF format, Adobe Reader/Acrobat Reader/Acrobat is required. If Adobe Reader/Acrobat Reader/Acrobat is not installed on your system, please download it from the Adobe Systems Incorporated website (http://www. adobe. com). Congratulations!You have now completed the machine setup. Where to go from here. . . Once you have completed all steps in this document, see the Basic Guide for basic operations of all functions of your machine. For information on the driver software, see the Software Guide (included in the User Software CD). [. . . ] You have now completed the machine setup. Where to go from here. . . Once you have completed all steps in this document, see the Basic Guide for basic operations of all functions of your machine. For information on the driver software, see the Software Guide (included in the User Software CD). NOTE Remember to register your machine to ensure product support. [. . . ]