User manual CANON IRC 3580 - IRC 3580I BROCHURE

[. . . ] Toll-Free Live Tech Support -- (1-800-828-4040) This option provides live telephone technical support, free of service charges, MondaySaturday (excluding holidays), during your product's 1 year limited warranty period. Telephone Device for the Deaf (TDD) support is available at (1-866-251-3752). 4. Extended Service and Support -- www. canonesp. com Canon CarePAK Extended Service Plan is a cost-attractive and easy-to-use extended service program that provides up to three full years of service and support coverage at a very attractive price. CarePAK offers toll-free Canon technical support and includes Canon's superb InstantExchange product replacement program. [. . . ] Determine if the fax switches to document receive mode after the fax rings for a specified time when the fax is in the manual receive mode. Set the amount of time the fax will ring before switching to document receive mode. If you set REMOTE RX to ON, you can select the remote receiving ID. Set whether the fax prints out received documents even when the ink level is low. Faxes will be deleted from memory after printing. If there is no ink left, the information contained in the fax will be lost. This setting will be retained even if the FINE cartridge is replaced with a new cartridge. If you select DRPD as the receive mode, select the ring pattern for the fax. ­ Settings ON/OFF 0 to 20 seconds 10 to 60 seconds DISCONNECT/ RECEIVE ON/OFF 2 to 30 times* ON/OFF RING TIME REMOTE RX REMOTE RX ID SAVE RX IMAGE OPTION SETTINGS 1 to 60 seconds ON/OFF 00 to 99 ON/OFF ON/OFF DRPD:SELECT FAX NORMAL RING DOUBLE RING SHORT-SHORT-LONG SHORT-LONG-SHORT OTHER RING TYPE * The values may differ depending on the country/region of use. Settings and Activity Reports 39 " PRINTER SETTINGS Name RX REDUCTION REDUCE DIMENSION PAPER SIZE INK SAVER Description Enable/disable reduction for received documents. Select reduction in height only or both width and height. Select the size of the loaded fax paper. See <TX REPORT> on page 38. Note A memory clear report is printed automatically when power is restored after a power failure. See "Memory Clear Report" on page 61. 42 Settings and Activity Reports Routine Maintenance Maintenance Menus The table below shows the available maintenance menus when you press [Maintenance]. Menus CS CLEANING (see page 50) NOZZLE CHECK (see page 46) CLEANING (see page 47) DEEP CLEANING (see page 47) ALIGN PRINT HEAD (see page 48) HEAD ALIGN VALUE (see page 48) ROLLER CLEANING (see page 51) BOTTOM CLEANING (see page 51) Replacing a FINE Cartridge If there is no improvement with the quality of printing following such maintenance as FINE Cartridge Cleaning, the FINE Cartridge is probably empty. Replace the empty FINE Cartridge with a new one. When replacing a FINE Cartridge, check the model number very carefully. The machine will not print properly if the wrong FINE Cartridge is used, or installed incorrectly. PG-40 Black PG-50 Black " Knowing When to Replace a FINE Cartridge !When Ink is Low When the ink level is low, <RECOMEND NEW CRT> is displayed on the LCD and the Ink Lamp lights up. In this state the FAX will receive documents to memory (up to 30 transactions or 60 pages) to prevent the information contained in the FAX from being lost if the ink runs out completely. You need to print out received faxes manually from the <MEMORY REFERENCE> menu. After printing, delete unnecessary faxes from the memory. [. . . ] The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five. Even if the dual-line option is installed, the REN is applicable to each port. 72 Appendix Avis L'indice d'équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d'une interface peut consister en une combinaison quelconque de dispositifs, à la seule condition que la somme d'indices d'équivalence de la sonnerie de tous les dispositifs n'excède pas 5. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. [. . . ]