User manual CANON LV-7545 BROCHURE

[. . . ] ◆ Simple Computer System Setting The projector has the Multi-scan system to conform to almost all computer output signals quickly (p. 34). ◆ Useful Functions for Presentation Digital zoom function allows you to focus on the crucial information during a presentation (pp. 14, 40). ◆ Security Function The Security function helps you to ensure security of the projector. With the Key lock function, you can lock the operation on the side control or remote control unit (p. 53). [. . . ] -M -N, PAL/SECAM/NTSC/NTSC4. 43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4. 43, PAL-M, and PAL -N. AV SYSTEM MENU (VIDEO OR S-VIDEO) AV System Menu icon The selected system is displayed Move the pointer to the desired system and press the OK button. Y, Pb/Cb, Pr/Cr Jacks Auto The projector automatically detects an incoming video signal, and adjusts itself to optimize its performance. When the Video System is 1035i or 1080i, select the system manually. COMPONENT VIDEO SIGNAL FORMAT If the projector cannot reproduce proper video image, select a specific component video signal format from among 480i, 575i, 480p, 575p, 720p, 1035i, and 1080i. AV SYSTEM MENU (COMPONENT VIDEO) AV System Menu icon The selected system is displayed. Move the pointer to the desired system and press the OK button. 41 Video Input Image Level Selection Menu Operation 1 2 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Select Menu icon. Use the Point ed buttons to move the red frame pointer to the desired image level and then press the OK button. IMAGE SELECT MENU Image Select Menu icon Standard Normal picture level preset on the projector. Cinema Picture level adjusted with fine tone. Custom 1–10 User preset picture adjustment in the Image Adjust Menu. 47) Move the red frame pointer to the desired level and press the OK button. 42 Video Input Screen Size Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Screen Menu icon. Use the Point ed7 8 buttons to correct keystone distortion. (p. 29) Ceiling When this function is set to “On, the picture is top/bottom and ” left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to “On, the picture is left/right reversed. ” This function is used to project the image from the rear of the screen. Reset This function returns all adjusted values to the factory default settings. Press the OK button at Reset to display a confirmation box. To reset, press the OK button at “Yes. ” Rear SCREEN MENU Move the red frame pointer to a function and press the OK button. Ceiling Quit Exit the Screen Size Adjustment Menu. 44 Picture Image Image Adjustment 1 2 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. Use the Point ed buttons to move the red frame pointer to the desired item and then press the OK button to display the adjustment dialog box. [. . . ] (See p. 20) Launch a communication software provided with PC and setup the communication condition as follows: Baud rate Parity check Stop bit Flow control Data bit : 9600 / 19200 bps : none :1 : none :8 ✔Note: • The default of the baud rate is set to 19200 bps. If an error occurs in the communication, change the serial port and the communication speed (baud rate). 3 Type the command for controlling the projector and then enter the "Enter" key. Example When you want to change the input to INPUT 2, Type 'C' '0' '6' 'Enter'. ✔Note: • Enter with ASCII 64-byte capital characters and onebyte characters. 78 Appendix Functional Execution Command Format The command is sent from PC to the projector with the format below; 'C' [Command] 'CR'  Command: two charactors (refer to the command table below. -The projector decodes the command and returns the 'ACK' with the format below; 'ACK' 'CR' -When the projector can not decode the command, it returns with format below. [. . . ]