User manual CANON LV-7575 EXPAND SERIAL COMMAND FUNCTIONAL SPECIFICATIONS

[. . . ] —  ake sure to fully insert the power plug and connectors when connecting the projector. m Never use a damaged plug or loosen outlet. —  o not drop this attachment or place heavy objects onto it. In particular, be careful not D to let children hang from the attachment. [. . . ] —  hen using the wall attachment to install the projector to a wall, make sure that the wall is W strong enough to support the combined weight of the projector and the wall attachment. Before carrying out installation, check the weight of the projector and the weight of the wall attachment, and then check the strength of the wall. If the wall is not strong enough, provide it with sufficient reinforcement. If this is not done, the projector may fall down and injury may occur. —  hen installing the projector, take appropriate measures using wire or other means to W p  revent falling due to an earthquake or other vibration. Otherwise, the projector may fall, causing injury. English To Use the Projector Properly ●  e sure to install the ceiling attachment so that there is at least 50 cm between the  B projector’s air intake vent and the wall, and at least 1 m between the air exhaust vent a  nd the wall. ●  se a flat , stable surface as the screen. In addition, if projecting onto a wall or similar U surface, the images may not be projected correctly if the wall is uneven or curved. 1 Template sheet for installing the wall plate. 4 (for securing setting plate and wall plate) M5 x 10 mm hexagon socket head cap bolt. ) Bolts (M8) x 4 (supplied) 5 Securing the projector to the adjustment unit A q  ttach the adjustment unit to the projector using the 5 screws (M4 x 18) which are supplied. Screws (M4) x 5 (supplied) Adjustment unit Projector R w  emove the two bolts (for drop-prevention) from the setting plate. Loosen the four bolts located on the top of the adjustment unit and set the projector with the adjustment unit onto the setting plate. Bolts (for drop-prevention) x 2 Loosen bolts x4 Setting plate Projector with the adjustment unit T e  ighten the four bolts which were loosened to secure the projector to the setting plate. Attach the two bolts (for drop-prevention) to the setting plate. Bolts (for drop-prevention) x 2 6 English ■ Installation Procedure Adjustment A q  djust the forward/backward slide (Adjustable range: 0 - 180 mm) ¡¡Loosen the four bolts on the top of the adjustment unit using a hexagon wrench (3 mm) and adjust the slider of the adjustment unit. After the adjustment, tighten the four bolts which were loosened. 09 inches (0 - 180 mm) A w  djust the vertical slide (Adjustable range: +4° - –2°) ¡¡Remove the left and right cover plates of the wall plate. ¡¡Loosen the four bolts A located inside the setting plate using a hexagon wrench (6 mm). ¡¡Adjust the vertical slide with the two bolts B located inside the setting plate using a hexagon wrench (6 mm) (Adjust the left and right bolts so that their ends touch equally against the wall plate. ) ¡¡Tighten the four bolts A which were loosened using the hexagon wrench (6 mm). [. . . ] Adjustment knob B 5° Bolt A 5° * “B” marks appear on the setting plate to indicate the locations of the bolt and adjustment knob. A t  djust the horizontal roll (Adjustable range: +5° - –5°) ¡¡Loosen the bolt A located on the front right side of the adjustment unit using a hexagon wrench (3 mm) so that adjustment can be carried out. ¡¡Turn the adjustment knob B located on the top-right side of the adjustment unit to adjust the horizontal roll. ¡¡Tighten the bolt A which was loosened using the hexagon wrench (3 mm). [. . . ]