User manual CANON NAGY FORMÁTUMÚ NYOMTATÓK - CAD/GIS TERMÉKCSALÁD BROSÚRA BROCHURE

[. . . ] For details on cable types and specifications, refer to page 2. ss Introduction s s s s s s s s s s s s s s s s s s s sssssssssssssssssss This Quick Start Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. Instructions that, if ignored, could result in death or serious personal injury caused by incorrect operation of the equipment. These must be observed for safe operation. Instructions that, if ignored, could result in personal injury or material damage caused by incorrect operation of the equipment. These must be observed for safe operation. [. . . ] Wait until the POWER lamp remains fully lit. 3 Open the front cover. 4 Remove the tape. 5 Raise the lock lever. Do not touch internal parts other than the lock lever. 4 6 Remove the protective cap from the print head. Notes Do not touch the print head nozzles or electrical contacts. Do not attempt to reattach the protective cap once it has been removed. electrical contacts print head nozzles print head 7 Place the print head in the holder. print head holder 8 Lock the print head into place by lowering the lever. Do not touch the lock lever once the print head has been installed. s Installing the Ink Tanks For safety reasons, store ink tanks out of the reach of small children. Do not drop or shake ink tanks. 1 Take out the yellow ink tank. 2 Pull the orange tape in the direction of the arrow and remove the clear film. 5 3 Hold the ink tank as shown in the diagram and remove the protective cap. Notes Do not squeeze the sides of the ink tanks as this may cause the ink to leak out and stain your clothes and hands. Do not attempt to reattach the protective cap once it has been removed. ink port 4 Insert the yellow ink tank into the righthand slot. Press the top until it clicks into place. 5 Use the same procedure to install the other ink tanks in their appropriate slots. Check the labels to make sure that each tank is in the correct position. Notes Only install the ink tanks in the positions specified by the labels. If ink tanks are not installed in the right position, colours will not be printed correctly. Immediately reinstall the tank in the correct position and carry out print head cleaning. For details, refer to the User's Guide. Magenta Yellow Black Photo Cyan Photo Magenta Cyan 6 Close the front cover. Wait until the POWER lamp remains fully lit. 6 ss 4 s Loading Paper s s s s s s s s s s s s s s s s s ssssssssssssssss s Loading A4 (Letter) Size Plain Paper paper thickness lever 1 Open the front cover. 2 Move the paper thickness lever at the top of the print head holder to the left position. Close the front cover. Note Set the paper thickness lever to the left when using plain paper, to the right when using thick paper. 2 Click Utilities. 3 Select Test Print from the menu and click the Print Head Alignment icon. 4 Check that paper is loaded in the printer and click OK. If the pattern is not printed successfully, open the front cover and ensure that the ink tanks are correctly installed. 5 Look at the print-out. From the patterns in Column A, select the most even, least irregular pattern and enter the number. 14 6 In the same way, one by one, select the most even patterns printed with the least irregularities from each of Columns B to F, enter their numbers and click Send. 7 Click Close. 8 Click OK. This completes the printer setup. The printer is now ready to use. 15 Basic Operations If you detect smoke, unusual smells or strange noises around the printer, immediately switch the printer off and always unplug the printer. Contact your local Canon service representative. To avoid injury, never put your hand or fingers inside the printer while it is printing. ss Printing with Windows s s s s s s s s s s s s s s s ssssssssssssss Adjusting the print settings according to your needs allows you to produce better quality prints. In this section, we will use WordPad for the purpose of explanation. The procedures you use and the screens that appear on your computer may differ according to the application that you use. s Printing 1 Print the document from the application. On the File menu, click Print. Check the application's user's manual for the actual procedures. 4 Specify the print settings according to your requirements. For details, refer to "Basic Print Settings" on page 19. 5 Click the Print button. Printing will start in a few moments. 18 s Page Setup Use the Page Setup dialog box to specify the paper size settings. Select paper size you wish to use. s Basic Print Settings For the best print quality, specify the minimum requirement settings in the Print dialog box. To get the best results, ensure you select the type of media loaded in the printer when printing on paper other than plain paper. (3) (2) (1) (1) Media Type (2) Print Mode Select the type of media loaded in the printer. Select the icon closest to the type of document you want to print. To specify more detailed settings for the print quality or colour, select Manual and click Details. . . . [. . . ] 5 Reinstall the printer driver (see page 8). For Further Details. . . For more information, place the Setup Software & User's Guide CD-ROM in the CD-ROM drive. s User's Guide Contents The "User's Guide" is in PDF format and can be found on the same CD-ROM as the printer driver. You can view this Guide on screen and print out any sections you require. Contents Printer parts and their functions Printer driver functions Routine maintenance Printing media Troubleshooting Specifications s How to View the User's Guide For Windows (1) Load the CD-ROM in your computer. (2) Click Manual at the bottom left of the screen. [. . . ]