User manual CANON NAGY FORMÁTUMÚ NYOMTATÓK - NYOMDAI TERMÉKCSALÁD BROSÚRA BROCHURE

[. . . ] Macintosh, Power Macintosh and Mac OS are trademarks of Apple Computer, Inc. , registered in the U. S. ScanSoft and OmniPage are trademarks of ScanSoft, Inc. Other names and products not mentioned above may be trademarks or registered trademarks of their respective companies. In this guide, Windows XP screen shots are used to illustrate explanations common to all operating systems. 2 Checking the Package Contents Scanner and Accessories CanoScan LiDE 500F USB Interface Cable Film Guide (for 35 mm film strip) Film Adapter Unit Documents and Software Programs · Quick Start Guide (this guide) · Additional Documents · CanoScan Setup Utility CD-ROM ScanGear CS - Scanner Driver It allows you to scan and load images from the scanner. CanoScan Toolbox - Scanning Utility Program It allows you to scan, save, or print images easily as well as create e-mail attachments or PDF files. [. . . ] · Before setting the stand, make sure that there isn't a space between the document cover and the surface of the document glass (p. 11, Step 3). 1 Turn the scanner upside down. 2 Lift the stand on the scanner back in the direction of arrow and then arrow . 3 Place the stand's end around the front side of the scanner (arrow ). 4 Push to the direction of arrow until marks on the scanner and the the stand align. 5 Slowly turn the scanner over and set it upright on the stand in position. 7 English Setting the Stand Connecting the Scanner Connecting the Scanner 1 Connect the scanner to the computer with the supplied USB interface cable. USB Connector Wide Flat Connector Small Square Connector USB Interface Cable · Only use the USB interface cable provided with the scanner. Use of other cables may lead to a malfunction. · When the scanner is connected to the USB 1. 1 port on Windows XP and "HI-SPEED USB Device Plugged into non-HI-SPEED USB Hub" message appears, ignore the message. The scanner operates in this condition without problems. · The scanner does not have a power switch. The power is activated as soon as the computer is turned on. There are cable holders on the side of the scanner to hold the USB cable. Hold the cable with the holders before setting up the stand in the upright position. Cable Holders 8 Positioning Items Items can be scanned in three different ways: scanning standard items, scanning oversize items, and scanning on the stand. The following procedures explain how to position items for each method. · Use a blower brush to remove any dust from the film, which will affect the image quality, and take care to hold the film by its edges to avoid transferring dirt or fingerprints to it. 1 Attach the cable for the film adapter unit to the FAU connector on the scanner's side panel. 2 Open the document cover and place the film guide on the document glass of the scanner. Fit the two tabs on the film guide into the document glass slots. · When opening the document cover, support it with your hand until it stops. Calibration Calibration is required when film is first scanned. Calibration is the process ScanGear CS uses to adjust to the correct color balance. If there is film in the film guide, remove it before setting the film adapter unit on it. 1 Remove the cap from the film adapter unit and gently set the film adapter unit over the first frame in the film guide. Align the tab on the film adapter unit with the film guide. · Be careful not to lose the cap or to allow dirt into it. 16 Scanning Film 2 Gently close the document cover. · Do not press down on, or rest your hands on the document cover. 3 Start ArcSoft PhotoStudio. Refer to step 2 on page 12. 4 Start ScanGear CS. Refer to step 4 on page 13. ScanGear CS will start. 5 Select a Select Source option. You can select from the following options for films. Negative Film (Color) / Positive Film (Color) 6 Click [Preview]. The "Executes calibration. " message will display. 7 Click the [OK] button. The calibration process will start and take approximately 1 to 2 minutes. The calibration process is finished when the message disappears. · Do not touch the scanner while it is operating. 8 To go on to scan films, follow steps 1-3 on the next page and click the [OK] button. The preview scan will start. Read from Step 8 onward in procedures for "Scanning Film" (p. To stop scanning film, click [Cancel]. 17 English Scanning Film Scanning Film 1 Place the film in the film guide. White Line Place the film face up in the film guide (images and words should read correctly from above) with the spaces between frames aligned with the white lines on the guide. 2 Remove the cap from the film adapter unit and gently set the unit over the frame you wish to scan. Align the tab on the film adapter unit with the film guide. [. . . ] The fastest speed in USB 2. 0 Hi-Speed mode on Windows PC. Transfer time to computer is not included. *3 Calibration processing time is not included. · Note that Macintosh computers with USB 2. 0 Hi-Speed interface expansion cards are not supported. [. . . ]