User manual CANON PIXMA MX372 BROCHURE

[. . . ] Raise the top cover. Documentation and Software Kit Remove the shipping tape and lower the inner cover. Top Cover Print Head Nozzles click Electrical Contacts USB Cable USB Port For Parallel Port: Inner Cover 4 Insert the remaining four ink tanks into 1 TURN THE PRINTER OFF. 2 Connect one end of the parallel cable to their assigned slots. 3 Raise the print head lock lever. the computer, the other to the printer. PIXMA iP4000 Series Print Head Front Cover 4 4 The print head holder automatically moves 5 Close the inner cover, then the top cover. to the center. Remove the protective tape. Lift open the paper support and extend the paper output tray. Paper Support Top Cover Power Cord 4 Slide the print head into the holder. The print head will rest at a slight angle. Inner Cover Parallel Cable 3 Remove the shipping tape from the paper Paper Output Tray Ink Tanks BCI-6Y Yellow BCI-6BK Black BCI-3eBK Black BCI-6M Magenta BCI-6C Cyan 5 Write down the serial number located to NOTE: The printer will perform a print head cleaning. [. . . ] Wait until the POWER lamp displays a steady green light before proceeding. 5 Lower the print head lock lever and press guide. Pinch the paper guide and slide it to the left. Load a few sheets of blank paper into the auto sheet feeder, then slide the paper guide toward the left edge of the paper. Auto Sheet Feeder the right of the print head holder. You will need this later to register the product. it down until it clicks into place. Paper Guide click Serial Number Location Continue with Step 6 on side two. 6 Cassette Loading NOTE: Loading paper in the cassette provides additional paper handling flexibility. For additional information visit the electronic User's Guide. 2 Remove the top cover of the cassette. 3 Slide the long edge paper guide to the left and 5 Replace the top cover of the cassette. 7 Ensure that the auto sheet feeder lamp is the short edge paper guide toward you. Top Cover Top Cover Long Edge Guide Short Edge Guide lit. The setup program should run automatically. NOTE: If the setup program does not run, click Start, then Run, then type D:\msetup. exe, where D is your CD-ROM drive. 3 When the main menu appears, 6 Follow the on-screen instructions to register then follow the on-screen instructions. 9 Follow the on-screen instructions. When the your product. 7 When the "Print Head Alignment" screen "Installation has finished" screen appears, click OK. appears, ensure that letter size paper is loaded in the auto sheet feeder (top paper feeder). Click Execute and follow on-screen instructions. 10 Double-click on the Product Registration d. Ensure that letter size paper is loaded in the auto sheet feeder (top paper feeder). Click the down-arrow to select Test Print. Click the Print Head Alignment icon and follow the on-screen instructions. icon, found in the Mac OS X folder, to register your product. click Easy Install. NOTE: When the "Authenticate" screen appears, enter your administrator name and password. If you do not know your administrator name or password, click , then follow the on-screen instructions. 4 When the message "The software was successfully installed" appears, click Restart. NOTE: Print head alignment will take several minutes to complete. 8 When the "Installation completed successfully" 5 When a message asking you to align the print head appears, click OK. NOTE: Print head alignment will take several minutes to complete. NOTE: Select Easy Install in order to install all of the application software, electronic manual and printer driver. [. . . ] If you do not know your administrator name or password, click , then follow the on-screen instructions. 4 When the message "The software was successfully installed" appears, click Restart. NOTE: Print head alignment will take several minutes to complete. 8 When the "Installation completed successfully" 5 When a message asking you to align the print head appears, click OK. NOTE: Print head alignment will take several minutes to complete. NOTE: Select Easy Install in order to install all of the application software, electronic manual and printer driver. Select Custom Install in order to choose the options you would like to install. screen appears, click Restart. Part no. QA7-3281-V01 © 2004 Canon U. S. A. , Inc. [. . . ]