User manual CANON PIXMA MX392 MX390 SERIES MANUAL DE USUARIO (OS X 10.6/10.7/10.8) [SPANISH VERSION]

[. . . ] 20 Specifying How Many Copies to Print for Each Photo ­ Multi-photo print. 22 23 Searching for Photos with the Shooting Date. 23 Printing a Specified Area ­ Trimming . 26 Printing on the Sticker ­ Sticker print . [. . . ] See "Changing the Bluetooth Settings--Bluetooth settings" on page 45. Communication is possible up to about ten meters depending on the conditions below. The printing speed may change depending on the following conditions: - Presence of obstacles between the communication equipment and radio wave conditions. - Presence of magnetic fields, static electricity or electromagnetic interference. - Receiver sensitivity and antenna performance of the communication equipment. For the transmittable data, see "About transmittable data" on page 43. 44 Changing the Bluetooth Settings--Bluetooth settings You can change the Bluetooth settings such as device name of a printer and passkey. 1 2 3 Turn on the printer. Connect the Bluetooth unit BU-20 to the direct print port. The Bluetooth settings screen does not appear until the Bluetooth unit is connected. Display the Bluetooth settings screen. (1) Press the Menu button. (3) Use the buttons to select Maintenance/settings and then press the OK buttons to select Device settings and then press the OK button. (4) Use the buttons to select Bluetooth settings and then press the OK button. The Bluetooth settings screen is displayed. 4 Change the setting. (1) Use the (2) Use the button. buttons to select the setting item you want to change. buttons to select the items you want to set then press the OK Setting Items · Device name name: Select the device name of this printer displayed on the screen of the Bluetooth devices. To use the card slot of the printer as the memory card drive of the computer, the printer must be connected to the computer, and the Memory Card Utility must have been installed for Windows Me/Windows 98/Windows 98 Second Edition. If the utility is not installed, install it following the installation procedure explained in the Easy Setup Instructions. When Read/write mode is selected, you cannot print photo in the memory card. After you are finished with using the card slot as a memory card drive for your computer, remove the memory card, then be sure to select Read-only mode again. 1 2 Ensure that both the printer and the computer are turned on, and connected by a USB cable. Display the Read/write attribute screen. (1) Ensure that no memory card is in card slot. If a memory card is in the card slot, remove it. (3) Use the buttons to select Maintenance/settings and then press the OK button. (4) Use the buttons to select Device settings and then press the OK button. (5) Use the buttons to select Other settings and then press the OK button. (6) Use the buttons to select Read/write attribute and then press the OK button. 3 Specify the Read/write attribute. (1) Use the buttons to select a mode. - When selecting Read/write mode, the card slot is used as the memory card mode drive of the computer. [. . . ] 7 Digital Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Digital Camera (Troubleshooting) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 DPOF print . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 31 N Noise reduction (Card Direct) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Noise reduction (PictBridge) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Nozzle check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Nozzle Check Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]