User manual CANON POWERSHOT A1300 BROCHURE

[. . . ] More than 99. 99% of the pixels operate to specification. Less than 0. 01% of the pixels may occasionally misfire or appear as red or black dots. This has no effect on the recorded image and does not constitute a malfunction. Video Format Please set the camera's video signal format to the one used in your region before using it with a TV monitor ( Please read through the "Read This First" section ( Disclaimer · While every effort has been made to ensure that the information contained in this guide is accurate and complete, no liability can be accepted for any errors or omissions. Canon reserves the right to change the specifications of the hardware and software described herein at any time without prior notice. [. . . ] 2 Press the or button : Left to right horizontally. : Right to left horizontally. to select the sequence direction, and then press the SET button. 3 Take the first shot. 50 4 Compose the next shot, taking care to overlap the previous image. · Minor discrepancies in the overlapping portions can be corrected when the images are stitched together. · If you are not satisfied with the previous shot, you can use or button to return to that shot and reshoot it. 5 Take additional shots for the panorama in the same way. You can take as many as 26 images. · You can adjust the following settings before taking the first shot: zoom, flash (On, Off, or Slow-synchro only), self-timer, macro or infinity mode, exposure compensation, white balance, resolution, and compression. These settings are locked in after the first image, and cannot be changed for subsequent shots. · Auto and red-eye reduction flash modes and digital zoom are not available when shooting in Stitch Assist mode. · PowerShot A20 users : It is not possible to display images on the TV monitor when shooting in Stitch Assist mode. 6 After taking the final image, press the SET button. 51 Functions Available in Each Shooting Mode The following chart shows the functions and settings available in each shooting mode. The camera stores settings separately for each mode, and retains these settings even if you switch to a different mode. Function Resolution Large Medium Small Superfine Fine Normal Red-eye reduction, Auto Auto On Off Slow-Synchro Auto * Manual * Stitch Assist * See page. . . 37 Compression * * _ * * _ _ * p. 47 Macro Mode Infinity Mode Shooting Method Single Continuous Self-Timer Digital Zoom Exposure Compensation White Balance * : Default, : Available, : Available, but cannot be changed after taking the first shot, _ : Not available, : Setting is retained even after power off. 52 Replaying Displaying Images Singly (Single Image Replay) Use this feature to view recorded images one at a time on the LCD monitor. 2 Use 2 1 and button to display different images. · Press button to move to the previous image. · Press button to move to the next image. · Hold down or button to cycle continuously. dial . Be careful to avoid accidental erasures. · This function will not erase protected images ( p. 58). 2 Press the MENU button to display the menu. 3 Press 4 Press or button to , and then press the select SET button. 3, 4, 5 2, 6 1 or button to select the image you wish to erase, and then press the SET button. The LCD monitor asks for confirmation. 1 Turn the mode dial to . 59 5 Press or button to select [OK], and then press the SET button. · If you decide you don't want to erase the image, select [Cancel] instead of [OK]. · To delete additional images, repeat Steps 4 and 5 as necessary. Erasing All Images · Remember that erased images cannot be recovered. Be careful to avoid accidental erasures. · This function will not erase protected images ( p. 58). 6 Press the MENU button to close the erase function. A faster way to delete an image is to replay it and then press the / button ( p. (But note that this quick-erase feature is disabled if the camera is connected to the optional Card Photo Printer CP-10. ) 1 Turn the mode dial to 2 Press , and press the MENU button to display the menu. or button to , and then press the select SET button. 60 The LCD monitor asks for confirmation. 3 Press or button to select [OK], and then press the SET button. · If you decide you don't want to erase all unprotected images, select [Cancel] instead of [OK]. 61 Print Settings (DPOF Settings) Images on a CF card can be individually selected for printing in a specified number of copies. The print type and date or file number printing options can also be selected. These settings are compatible with Digital Print Order Format (DPOF) standards so that images can be printed conveniently on DPOF compliant digital printers or at participating photo labs. · The mark will display on images that have had print marks set by another DPOF-compliant camera. These settings will be overwritten by any settings set by your camera. [. . . ] 67 Print Style . . . . . . . . . . . . . . . . . . . . . . . . . 71 [Print Order] Menu . . . . . . . . . . . . . . . . . . 67 Resuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Z Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]