User manual CANON REALIS SX60

[. . . ] User Command Specifications 1 Cover Canon projector SX6/SX60/X600 User Commands ver. 01. 0100/01 2005. 12. 27 2005. 12. 5 2005. 11. 14 2005. 11. 10 2005. 11. 1 User Command Specifications Version revision history 1 I. Version revision history Numerical value 01. 0100/01 01. 0100/02 Date 2005. 11. 01 2005. 11. 10 I. Version revision history Description of revised version Where revised 01. 0100/03 2005. 11. 14 01. 0100/04 2005. 12. 05 01. 0100/05 2005. 12. 27 Version first created. [. . . ] (1) It can be executed when the projector is in both the remote mode and power-on status at the same time. However, a "busy" response is given while the zoom or focus lens is being driven. Refer to the ZCONTDRV command and FCONTDRV command. (2) This command functions in the same way as when first the "FOCUS" button on the remote control or main unit panel is pressed and then the "" or "" button is pressed. (3) The amount by which the lens is focused is constant, and it is fixed for the system. (4) If a focusing error occurs, step drive cannot be controlled. Example Control > FSTEPDRV=NEAR < I:OK Range acquisition > RANGE FSTEPDRV < r:FSTEPDRV=I, FAR, NEAR 1-step control is exercised over the zoom toward the NEAR end. "FAR" or "NEAR" can be set for focus step control. Commands supported SX50 SX6 SX60 X600 ** ** ** ** × When a command is not supported, "e:0002 INVALID_COMMAND" is returned. Supported Command States Model Power supply OFF ON PM D-RGB A-RGB1 A-RGB2 Comp Input Video S-Video D-Video SCART None Mode Remote Local × Remarks SX50 SX6 SX60 X600 ×× *If a state is not supported, "INVALID_MODE" or "NOT_POWER_SUPPLIED" is returned with the Err response. *When the power supply state is in the process of switching, an "i:BUSY" reply may be sent. PAGE 67 User Command Specifications Details of command FCONTDRV 1 FCONTDRV Commands FCONTDRV FCONTDRV=<Focus lens continuous control parameter> Mode Control Setting Reference Function Focus lens continuous drive control Format Parameter Focus lens continuous control parameters Parameter STOP FAR NEAR Meaning This stops the focusing. This initiates focusing toward the far end. This initiates focusing toward the near end. The parameters which can be set at any given point in time can be obtained using the RANGE command. For details, refer to the RANGE command. Response "i:OK" is returned when the drive was completed successfully. For all other responses, refer to "Error List. " Description This command is used to drive the focus lens. (1) It can be executed when the projector is in both the remote mode and power-on status at the same time. However, only the "STOP" parameter takes effect while the focus lens is being driven, and a "busy" response is given while the zoom lens is being driven. Refer to the ZCONTDRV command and FCONTDRV command. (2) This command functions in the same way as when first the "FOCUS" button on the remote control or main unit panel is pressed and then the "" or "" button is pressed. (3) Focus drive is started by specifying "NEAR" or "FAR. "To stop the drive, add the "STOP" parameter and send this command. If no instruction was given to stop the drive, the drive stops at the drive direction end. (4) The following commands are acknowledged during focus drive, but focus drive will also stop at the same time. In the case of any other commands, "i:BUSY (FOCUS)" is returned unconditionally, and focus drive continues. REMOTE LOCAL POWER FCONTDRV=STOP (5) The following commands are acknowledged during focus drive, and a response is returned while the drive continues. [. . . ] The current input signal is indicated in parentheses. Signal setting (detection) is in progress. Preparing to switch to power management standby. Heavy processing is in progress. Change the input source. [. . . ]