User manual CANON REALIS SX7 MARK II BROCHURE

[. . . ] Version number of User Commands changed to "01. 0100. " Entire document Listing of the parameters for each command changed to the listing obtained by the "RANGE" command. Entire document "Character interval timeout" in communication specifications changed from 10ms to 5 seconds (timeout PAGE 2 between CR and LF is 10ms). "GUID" in "User Command System" changed to "GUIDE. " PAGE 8 PAGE 12 "GUID" in "Command List" changed to "GUIDE. Condition added to "RC/MAIN commands" as a condition for returning from power management standby PAGE 11 in "Power Management Mode. " "AUTOSETEXE" command changed from a "setting" command to a "control" command. [. . . ] In the case of any other commands, "i:BUSY (ZOOM)" is returned unconditionally, and zoom drive continues. REMOTE LOCAL POWER ZCONTDRV=STOP (5) The following commands are acknowledged during zoom drive, and a response is returned while the drive continues. GET GET GET GET MODE POWER ERR LAMPCOUNTER e. GET PRODCODE GET ROMVER GET COMVER (6) Zoom drive stops when the "POWER" button on the remote control or main unit panel is pressed during zoom drive. Example Control > ZCONTDRV=TELE < I:OK Range acquisition > RANGE ZCONTDRV < r:ZCONTDRV = I, STOP, WIDE, TELE Control over the zooming to the telephoto end is started. "STOP, " "WIDE" or "TELE" can be set for zoom lens continuous drive. Commands supported SX50 SX6 SX60 X600 ** ** ** ** × When a command is not supported, "e:0002 INVALID_COMMAND" is returned. Supported Command States Model Power supply OFF ON PM D-RGB A-RGB1 A-RGB2 Comp Input Video S-Video D-Video SCART None Mode Remote Local × Remarks SX50 SX6 SX60 X600 ×× *If a state is not supported, "INVALID_MODE" or "NOT_POWER_SUPPLIED" is returned with the Err response. *When the power supply state is in the process of switching, an "i:BUSY" reply may be sent. PAGE 66 User Command Specifications Details of command FSTEPDRV 1 FSTEPDRV Commands FSTEPDRV FSTEPDRV=<Focus lens step control parameter> Mode Control Setting Reference Function Focus lens step drive control Format Parameter Focus lens step control parameters Parameter Meaning FAR This initiates focusing toward the far end. NEAR This initiates focusing toward the near end. The parameters which can be set at any given point in time can be obtained using the RANGE command. For details, refer to the RANGE command. Response "i:OK" is returned when zooming was completed successfully after step drive. For all other responses, refer to "Error List. " Description This command is used to drive the focus lens. GET GET GET GET MODE POWER ERR LAMPCOUNTER e. GET PRODCODE GET ROMVER GET COMVER (6) Focus drive stops when the "POWER" button on the remote control or main unit panel is pressed during focus drive. Example Control > FCONTDRV=NEAR < I:OK Range acquisition > RANGE FCONTDRV < r:FCONTDRV=I, STOP, FAR, NEAR Control over the focusing to the near end is started. "STOP, " "FAR" or "NEAR" can be set for focus lens continuous drive. Commands supported SX50 SX6 SX60 X600 ** ** ** ** × When a command is not supported, "e:0002 INVALID_COMMAND" is returned. Supported Command States Model Power supply OFF ON PM D-RGB A-RGB1 A-RGB2 Comp Input Video S-Video D-Video SCART None Mode Remote Local × Remarks SX50 SX6 SX60 X600 ×× *If a state is not supported, "INVALID_MODE" or "NOT_POWER_SUPPLIED" is returned with the Err response. *When the power supply state is in the process of switching, an "i:BUSY" reply may be sent. PAGE 68 User Command Specifications 9. Details of command RC 2 RC Commands RC RC<Remote control emulation button parameters> Mode Control Setting Reference Function Remote control operation emulate Format Parameter Remote control emulation button parameters The key assignment for the remote control emulation buttons is as follows. Remote control button POWER MENU AUTO SET COMPUTER1 COMPUTER2 VIDEO INPUT AUTOPC KEYSTONE UP DOWN LEFT RIGHT OK R_CLICK PAGE PAGE IMAGE FREEZE VOL + VOL VOL NOSHOW MUTE P-TIMER DZOOM + DZOOM_M SPOT FOCUS ZOOM Parameter POWER POWER_OFF MENU AUTOSET COMPUTER1 COMPUTER2 VIDEO INPUT AUTOPC KEYSTONE UP UP+REP DOWN DOWN+REP LEFT LEFT+REP RIGHT RIGHT+REP OK R_CLICK P_UP P_UP+REP P_DOWN P_DOWN+REP IMAGE FREEZE VOL_P VOL_M VOL NOSHOW MUTE P_TIMER DZOOM_P DZOOM_P+REP DZOOM_M DZOOM_M+REP SPOT FOCUS ZOOM *-REP Errors supported by model SX50 SX6 SX60 X600 Remarks POWER button pressed twice × × × × × × × × × × × × × × × × × × × × × × × × × × × × × Button press start Button press start Button press start Button press start ID Button press start Button press start Button press start Button press start Button press end *Use the application to adjust the time between pressing of keys. PAGE 69 User Command Specifications 9. Details of command RC Response "i:OK" is returned when the button press request has been acknowledged successfully. (It does not indicate if the operation for the pressed button was executed properly. ) Description This emulates pressing of the remote control buttons for controlling the projector. -1 It can only be used during Local mode. Note 1 With the emulation of the remote control operations, the functions of the buttons corresponding to the parameters cannot necessarily be executed. Emulation simply consists in emulating the pressing of the buttons. [. . . ] A communication protocol violation occurred in the projector. This cannot be executed with the current input source. The current input source is indicated in parentheses. This cannot be executed with the current input signal. [. . . ]