User manual CANON REALIS SX800 BROCHURE

[. . . ] P46-48 P44 Adjust the focus of the screen. Set up the computer. Turn on the computer and set the resolution. Select the input signal by pressing the Press the button again. Select an appropriate input signal in accord with the signal from the computer. Adjust the input signal, focusing, keystone distortion, etc. automatically with the auto setup function. Press the button. P52 Optimize the input signal with the auto PC function (Skip this step if the projector is projecting an image properly. ) Select the image mode with the button. P53-54 Select an appropriate image mode for projection. Specify the aspect ratio or display area in the [Aspect] menu as required (P55, 88). 10. Start the presentation. Finishing the projection. . . P76-81 Set the useful functions available during the presentation from the remote control. Turn off the projector Turn off the projector and unplug the power cord. P58-59 2 AV Equipment 1. [. . . ] Refer to page 44 for detailed information on items adjusted by performing the auto setup. 1 Select [DIGITAL VIDEO]. Perform the steps shown in the "Selecting DIGITAL VIDEO" section on page 68 before performing the auto setup if you want to project a digital content video image. Skip this step if [DIGITAL VIDEO] has been selected at the previous projection. The [Auto setup] window appears. 2 PROJECTING AN IMAGE FROM AV EQUIPMENT 3 Press the [AUTO SET] button again. One or more functions highlighted in black are performed automatically. You can perform this step by selecting [OK] with the [<] button, and then pressing the [OK] button. Selecting an Input Signal Select [DIGITAL VIDEO] among the following 4 input signals by following the steps shown in the "Selecting DIGITAL VIDEO" section below if you want to project a digital content video image. DIGITAL VIDEO : Digital signal Connecting with an HDMI/DVI cable or DVI digital cable COMPONENT : Component signal Connecting with a supplied component cable SCART : SCART signal Connecting with a supplied SCART cable VIDEO : Video signal Connecting with a video cable S-VIDEO : S-VIDEO Connecting with an S-Video cable The component, video, and S-VIDEO signals are automatically set if a cable is connected and the input signal is confirmed. A LED (green) on a terminal flashes when an input signal is confirmed. The LED turns on if the signal is selected and projected (P24, 25). Connecting with a HDMI/DVI cable, the image may be projected with the minimum resolution (480p or 575p) due to the specification of the AV equipment. 68 Selecting DIGITAL VIDEO 1 Press the [INPUT] button. The [INPUT] window appears. 2 Select the top item in the menu with the [INPUT] button. The selection is toggled through available input signal types from above. PROJECTING AN IMAGE FROM AV EQUIPMENT You can select any input signal type from all options through the [ ] / [ ] button. < 3 If [DIGITAL VIDEO] is unavailable from the list at the left, press [>], and then press [ ] / [ ] to select it from the list at the right. The following table shows the available [Aspect] mode for each input signal. Input signal VIDEO S-VIDEO SCART COMPONENT (480i/575i/480p/575p) DIGITAL VIDEO (480p/575p) COMPONENT DIGITAL VIDEO (720p/1035i/1080i) 4:3 Wide Available [Aspect] mode 4:3 Wide Wide PROJECTING AN IMAGE FROM AV EQUIPMENT Select [4:3] from the [Aspect] menu if you want to project a video image with aspect ratio of 4:3 in this mode (P71). Keystone adjustment will be disabled. Project the image at right angle to the screen. [Auto focus], [Auto keystone], and [Auto screen color] are disabled in the [Auto setup] function. You cannot register the image for [Projector on] or [No signal screen]. [SPOT] will be disabled. 73 Table of contents/Safety Instructions Before Use Setting Up the Projector USEFUL FUNCTIONS AVAILABLE DURING A PRESENTATION Projecting an Image from the Computer Projecting an Image from AV Equipment Useful Functions Available During a Presentation Setting Up Functions from Menus Maintenance Troubleshooting Appendix Index Useful Functions Available During a Presentation Blackened Out an Image Temporarily Useful when: You finished the presentation. You want to divert attendees' attention from the screen. Blackening out an Image Muting the Sound Useful when: You want to immediately mute the sound from the projector. Mute the sound temporarily. Muting the Sound The screen changes to black or blue. Showing the Image Again Press the again. button to show the image The projector shows the [MUTE] icon on the screen. Canceling the MUTE function Press the button again to cancel the MUTE function. [. . . ] 30, 129 Projector installation . . . . . . . . . . . . . . . . . . . . . . . . . 14, 31 Projector on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 P-TIMER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 W WARNING lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]