User manual CANON REALIS WUX10 MARK II D DICOM

[. . . ] 3 Control Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Communication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Response. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (6) The GET command can be used to retrieve the current vertical shift amount. For details, refer to the GET command. Example Setting > VDISHIFT=-23 > i:OK Reference > GET VDSHIFT or ?VDISHIFT < g:SCRNASPECT=16:9_DIS Obtain settable parameter range (Min, Max) > RANGE VDISHIFT < r:VDISHIFT=N, -131, 131 This sets the vertical shift amount to -23. This retrieves the vertical shift amount. Any value from -131 to 131 can be set for the vertical shift. * Commands are indicated by ">", and responses are indicated by "<". Commands supported This defines the environments that support the command (power supply state, input signal state). SX50 SX6 SX60 X600 SX7 X700 SX7 Mark II 01. 00** 01. 01** 01. 01** 01. 01** 01. 01** 01. 01** 01. 02** x x x x x x O * When a command is not supported, "e:0002 INVALID_COMMAND" is returned. Environment This defines the environments that support the command (power supply state, input signal state). Power Input Mode Model Remarks OFF ON PM D-RGB A-RGB1 A-RGB2 COMP Video S-Video D-Video SCART None Remote Local SX50 SX6, SX60, X600 SX7, X700 SX7 Mark II x O x O O O O O O O O O O O * If a state is not supported, "NOT_POWER_SUPPLIED" is returned with the Err response. * When the power supply state is in the process of switching, an "i:BUSY" reply may be sent. Revision History / Date Changes Revised by Approved by - 102 - Projector User Commands VKS/HKS Vertical/horizontal keystone setting Setting Format VKS=<Vertical keystone distortion value:Number> HKS=<Horizontal keystone distortion value:Number> Parameter <Vertical keystone distortion value:Number> <Horizontal keystone distortion value:Number> The RANGE command can be used to obtain the parameter range that can be set at that time. For details, refer to the RANGE command. Response "i:OK" is returned if the parameter was set properly. For details on other responses, refer to the "Error List". Description This sets the vertical and horizontal keystones. (1) For models other than SX7 Mark II: It can be executed when the projector is in both the remote mode and power-on status at the same time. For SX7 Mark II: It can be executed whenever the projector is in the power-on status. (2) A “busy” response is given while the zoom or focus lens is being driven. (Refer to the ZCONTDRV command and FCONTDRV command. ) (3) This command is identical to pressing the “KEYSTONE” button on the remote control or front panel. SX50 SX6 SX60 X600 SX7 X700 SX7 Mark II 01. 00** 01. 01** 01. 01** 01. 01** 01. 01** 01. 01** 01. 02** O O O O O O O Revision History / Date Changes Revised by Approved by - 105 - Projector User Commands Environment This defines the environments that support the command (power supply state, input signal state). Power Input Mode Model Remarks OFF ON PM D-RGB A-RGB1 A-RGB2 COMP Video S-Video D-Video SCART None Remote Local SX50 x O x O O O O O O O O x SX6, SX60, x O x O O O O O O O O O O x X600 SX7, X700 x O x O O O O O O O O O O x SX7 Mark II x O x O O O O O O O O O O O * If a state is not supported, "INVALID_MODE" or "NOT_POWER_SUPPLIED" is returned with the Err response. * When the power supply state is in the process of switching, an "i:BUSY" reply may be sent. Revision History / Date Changes Revised by Approved by - 106 - Projector User Commands WBRGB Screen color correction (ADJUST) Setting Format WBRGB=<R adjustment value:Number>▽<G adjustment value:Number>▽<B adjustment value:Number> Parameter <R adjustment value:Number>▽<G adjustment value:Number>▽<B adjustment value:Number> RGB setting value Each value –20 to 20 The parameters which can be set at any given point in time can be obtained using the RANGE command. For details, refer to the RANGE command. Response "i:OK" is returned if the parameter was set properly. For details on other responses, refer to the "Error List". Description This sets the RGB adjustment values of the screen color correction. (1) For models other than SX7 Mark II: It can be executed when the projector is in both the remote mode and power-on status at the same time. For SX7 Mark II: It can be executed whenever the projector is in the power-on status. (2) A “busy” response is given while the zoom or focus lens is being driven. (Refer to the ZCONTDRV command and FCONTDRV command. ) (3) Although this setting is enabled when Adjustment (ADJUST) is selected by the screen color correction command (WB), it can be made independently. (4) This command has the same function as the buttons listed in the table below. Model Menu SX50 [Image adjustments] - [Screen color correction] - [Adjustments] SX6, SX60, X600, SX7, X700, [Display settings] - [Screen color correction] - [Adjustments] SX7 Mark II (5) With this command, the R, G, and B values can be set in a single operation. [. . . ] O O O O An error occurred in AUTOSETEXE=FOCUS. A communication protocol violation occurred in the projector. Eliminate the cause of the error, and resend the command. Resend the command. O O O O O O O O O O O O O O Use the range command to obtain an Specified aspect cannot be set since the addressable parameter range to be set screen aspect is not 4:3. It cannot be executed due to current Change the screen aspect setting. It cannot be executed with the current O input source. [. . . ]