User manual CANON REALIS WX520 PRO AV DRAWING

[. . . ] The Form Specifications are not intended for any specific application or use and project specific considerations must be taken into account in the architect’s or engineer’s preparation of actual system specifications. Canon makes no representation or warranty with respect to these Form Specifications and nothing contained herein shall create, or be inferred to create, any express or implied warranty by Canon. These Form Specifications are intended solely to for the purpose of reflecting general guidelines for video surveillance system specifications, taking into account the features of the Canon model REALIS WX520 PRO AV in production as of the date hereof, as set forth under Sections 2. 02 B through 2. 02 P herein. Canon reserves the right to change the features or specifications of the aforementioned model at any time, without notice. [. . . ] The Contractor shall be responsible for initiating, maintaining, and supervising all safety precautions and programs in connection with the Work. Contractor shall comply with all local, state, and federal regulations and laws for the safety of the work place. Accident Reports Serious or fatal accidents shall be reported immediately by telephone or radio to the OWNER’s Project Manager. 2. 3. 4. 5. B. Existing Conditions Existing Wiring, Conduits, and Raceways 1. OWNER does not warrant the condition of any portion of the existing wiring, conduit or raceway systems. Prior to submitting his proposal, Contractor shall examine all existing conditions and determine to what extent the existing wiring, conduit, and raceway systems may be reused. OWNER / November 22, 2013 28 23 00 - 7 Video Surveillance System Canon model REALIS WX520 PRO AV A&E Specifications 2. Contractor’s proposal price shall include the cost of replacing existing wiring, conduit, and raceways as required. 1. 09 SEQUENCING A. Description This implementation plan describes the general approach that shall be followed in order to minimize the time for the access control systems to be operational. Approach Contractor shall plan and schedule all work in such a sequence as to minimize the time before the system is operational. The following is a suggested work sequence: 1. Order all equipment needed and notify any subcontractors to schedule their participation. Insure there are an adequate number of power receptacles available to operate all security equipment and coordinate with OWNER as to where power is available. Provide shop drawings to verify location of all equipment, conduit runs, power connections, etc. Contractor shall remove covers, open wiring connections, operate equipment, and perform other reasonable work as requested by OWNER. Any portions of the Work found to be deficient or not in compliance with the Project Drawing and Specifications will be rejected. OWNER Project Manager will prepare a list of any such deficiencies observed during the Acceptance Test & Inspection. Contractor shall promptly correct all deficiencies. Upon correction of deficiencies, Contractor shall submit a request in writing to OWNER Project Manager for another Acceptance Test & Inspection. If, at the conclusion of the Acceptance Test & Inspection, all Work is found to be acceptable and in compliance with the Project Drawings and Specifications, OWNER Project Manager will issue a letter of Acceptance to Contractor and OWNER. B. C. D. E. PART 2 PRODUCTS OWNER / November 22, 2013 28 23 00 - 9 Video Surveillance System Canon model REALIS WX520 PRO AV A&E Specifications 2. 01 GENERAL A. All products not provided by OWNER shall be new and unused, and shall be of manufacturer’s current and standard production. Where two or more equipment items of the same kind are provided, all shall be identical and provided by the same manufacturer. Drawings and Specifications indicate major system components, and may not show every component, connector, module, or accessory that may be required to support the operation specified. Contractor shall provide all components needed for complete and satisfactory operation. Contractor, prior to submitting a proposal, shall determine product availability and delivery time, and shall include such considerations into his proposed Contract Time. [. . . ] Use conduit bodies to make sharp changes in direction, as around beams. Fasten conduits and raceways to structural steel using approved spring clips or clamps. Where conduit penetrates fire-rated walls and floors, seal opening with UL listed fire rated sealer or other methods as approved by codes. No exposed conduit, raceway, or junction box shall be installed within any office area. [. . . ]