User manual CANON TINTENSTRAHLDRUCKER UND MULTIFUNKTIONSSYSTEME SORTIMENT 2010 BROCHURE

[. . . ] Gently rock the cartridge several times to distribute toner inside. Pull out the seal completely. NOTE Do not pull out the seal at an angle. CAUTION Do not open the drum protective shutter (A). 4 5 A 6 A 7 A Open the document feeder tray. Open the cartridge cover by the notch (A). Hold the cartridge by its handle (A). Insert the cartridge in the machine as far as it will go. The arrow (A) on the cartridge should be facing away from you and pointing down. 8 9 10 Push down the cartridge to make sure it is properly set in the machine. Close the cartridge cover. NOTE Be careful not to get your fingers caught. A B Open the paper delivery tray (A) and the extension (B). 3 4 Load Paper Load Paper 1 2 3 4 A5 B5 A4 LGL LTR EXEC Lift the paper stack cover and pull it out completely. NOTE Make sure the back end of the cover does not catch the front paper guide. Pinch and slide the side paper guides to the size of paper. Pull out the paper guide rail as far as it will go. Fan the paper stack and even the edges. 5 A 6 7 A A Insert the paper stack print side up. NOTE Make sure the stack height does not exceed the limit mark (A). Push back the paper guide rail to the front edge of paper. NOTE ­ If loading paper shorter than Letter, pinch and slide the front paper guide (A) to match the paper size. [. . . ] ­ If loading paper other than Letter, make sure to set the correct paper size in the machine. (See Chapter 3, "Print Media, " in the Basic Guide. ) Insert the paper stack cover. NOTE Make sure the back end of the cover does not catch and lower the scanning platform (A). 8 B A Pull out the document delivery tray (A) and the extension (B). Do not open or close the document delivery tray extension without extending the document delivery tray first. 5 6 Connect Telephone Cables and Install Handset Connect Telephone Cables C Install Handset 1 2 A B A Use a screwdriver to remove the covers on the left side of the machine. Insert the plugs with pins (A) into the holes on the handset cradle. NOTE Do not insert the pins all the way into the plugs at this point. Connect the supplied telephone cable to the line jack (A) and the wall jack. Connect the handset cable to the handset jack (C). Connect any external device to the external device jack (B) if required. 3 4 5 6 A Insert the plugs (with the cradle) into the holes on the machine. Carefully push the pins into the plugs as far as they will go. Place the handset on the cradle. Hook the handset cable on the retainer (A) at the back of the machine to retain the slack. NOTE If using the handset or an external telephone, make sure to set the fax receive mode to <FAX/TEL>, <MANUAL>, or <DRPD>. For instructions on how to set the receive mode, see "Set the Receive Mode, " on p. 16. 7 8 Connect Power Cord Connect Power Cord 1 2 16:00 -SET STD DOC. - FAX 100% ONLY Connect the power cord into the rear socket and the wall outlet to turn on the machine. The machine enters the standby mode. What if. . . <CARTRIDGE COVER OPEN> is displayed: Make sure that the cartridge cover is closed properly. (See "Install Cartridge, " on p. 3. ) <NO TONER CARTRIDGE> is displayed: Make sure that the cartridge is installed properly. (See "Install Cartridge, " on p. You have to manually receive faxes. NOTE For <AnsMode>, make sure an answering machine is connected to the machine. No <FAX/TEL> Switches between fax and voice calls automatically. Yes <DRPD> Distinguishes between fax and voice calls. NOTE ­ The answering machine must be connected directly to the machine for <AnsMode> to work. ­ Voice mail is not supported with <AnsMode>. ­ The <DRPD> mode requires subscription to a DRPD (Distinctive Ring Pattern Detection) service. Contact your telephone company for availability. 15 16 Install the Printer Driver Installation Procedure Before Installation: · Do not connect the USB cable before installing the software. If you connect the USB cable before installing the software and the Found New Hardware Wizard screen appears, click [Cancel]. · For Windows 2000/XP, log on as Administrator to install the software. · Make sure the machine is turned on before connecting the USB cable. · On the screen shown at each step, click on the circled button to proceed. System Requirements Microsoft Windows 98/98SE CPU: Intel 80486DX/66 MHz or faster Memory: 24 MB or more Available Hard Disk Space: 355 MB or more Microsoft Windows Me CPU: Intel Pentium/150 MHz or faster Memory: 32 MB or more Available Hard Disk Space: 295 MB or more Microsoft Windows 2000 Professional CPU: Intel Pentium/133 MHz or faster Memory: 64 MB or more Available Hard Disk Space: 655 MB or more Microsoft Windows XP (32-bit version) CPU: Intel Pentium/Celeron series 300 MHz or faster Memory: 128 MB or more Available Hard Disk Space: 1. 5 GB or more 1 2 3 If the L120 CD-ROM Setup screen is not displayed, on the Windows desktop, double-click [My Computer]. Open the CDROM icon, then double-click [Mlnst (Mlnst. exe)]. 4 5 6 7 8 9 10 11 12 13 14 A Connect the machine and your computer with a USB cable (A). You have now completed machine set-up. Canon and FAXPHONE are registered trademarks, and UHQ is a trademark of Canon Inc. [. . . ] · On the screen shown at each step, click on the circled button to proceed. System Requirements Microsoft Windows 98/98SE CPU: Intel 80486DX/66 MHz or faster Memory: 24 MB or more Available Hard Disk Space: 355 MB or more Microsoft Windows Me CPU: Intel Pentium/150 MHz or faster Memory: 32 MB or more Available Hard Disk Space: 295 MB or more Microsoft Windows 2000 Professional CPU: Intel Pentium/133 MHz or faster Memory: 64 MB or more Available Hard Disk Space: 655 MB or more Microsoft Windows XP (32-bit version) CPU: Intel Pentium/Celeron series 300 MHz or faster Memory: 128 MB or more Available Hard Disk Space: 1. 5 GB or more 1 2 3 If the L120 CD-ROM Setup screen is not displayed, on the Windows desktop, double-click [My Computer]. Open the CDROM icon, then double-click [Mlnst (Mlnst. exe)]. 4 5 6 7 8 9 10 11 12 13 14 A Connect the machine and your computer with a USB cable (A). You have now completed machine set-up. Canon and FAXPHONE are registered trademarks, and UHQ is a trademark of Canon Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. [. . . ]