User manual CANON VB-C50IR BROCHURE

[. . . ] LOS ANGELES OFFICE 15955 Alton Parkway, Irvine, CA 92618 USA CANON U. S. A. , INC. HONOLULU OFFICE 210 Ward Avenue, Suite 200 Honolulu, HI 96814 USA User's Manual If you have any questions, call the Canon U. S. A. Information Center toll-free at 1-800-828-4040 (U. S. A. only) CANADA CANON CANADA INC. NATIONAL HEADQUARTERS 6390 Dixie Road, Mississauga, Ontario L5T 1P7 CANON CANADA INC. [. . . ] r Setting number selection box Select the number of the setting you want to use. t Cancel Infrared Cut Filter Check to remove the camera's Infrared Cut Filter to enable shooting with black-and white images using infrared light. y Turn Infrared Light ON * Not available with the VB-C50Fi. u Enable Slow Shutter Check to select a shutter speed for the camera. 4-48 Schedule Setting Tool Setting Up Night Mode 1. With the Schedule Setting Tool, open the Night Mode Setting Tool. In the Service tab of the Schedule Setting screen for a Normal or Special Schedule, check Night Mode, select a setting number and click the "Detail" button ( P. 4-38), or click the "Night mode setting tool" button on the toolbar. If you have opened the Night Mode Tool from the toolbar, select a setting number from the setting number selection box in the Night Mode Setting screen. 2. Check Cancel Infrared Cut Filter. For setting slow shutter. 3. Click the "Save Settings" button to save the settings and close the Night Mode Setting screen. If you have selected "Enable Slow Shutter", exposure will be manual, and aperture and gain will be at maximum. Change the shutter speed and adjust brightness according to your operating environment and photographic subject. If you specify a shutter speed of 1/30 seconds or slower for NTSC, or 1/25 seconds or slower for PAL, auto focus will not operate. To Make Settings. . . Note Tip VB Administration Tools In Night Mode, focusing with Auto Focus may be difficult or may appear to be out of focus. 4-49 Schedule Setting Tool External Device Input Setting Tool Below is a description of the External Device Input function which performs video recording when a signal from an external device connected to the Multi-Terminal Module ( P. 1-10) such as a sensor is input into the device. External Device Input Setting Tool Display Screen qw e r t y u i o !0 !1 !2 !3 !4 !5 q "Load Settings" button Loads the External Device Input settings currently set in the VB-C50Fi. w "Save Settings" button Saves the External Device Input settings edited using this Tool. Also, enter the required number of seconds and the interval for picture recording before or after an ON or OFF event. If you check "E-mail notification on recording" you can send an e-mail of the recorded picture. 3. Click the "Save Settings" button to save the settings and close the External Device Input Setting screen. To Make Settings. . . Tip Tip See "Setting up name server address and mail etc. " ( P. 3-25) for the addresses of mail messages and communication methods and "E-Mail Notification Settings dialog box" ( P. 4-59) for setting content of mail messages. See "Relationship between ON and OFF events and picture recording" ( P. 4-58) for the ON and OFF events and picture recording relationship of each item. 4-51 Schedule Setting Tool External Device Output Setting Tool The section below describes the output settings to an external device connected to the MultiTerminal Module ( P. 1-10). External Device Output Settings Tool Display Screen qwe r t y u i q "Load Settings" button Loads the External Device Output settings currently set in the VB-C50Fi. w "Save Settings" button Saves the External Device Output settings edited using this Tool. After setting the External Device Output function, be sure to click the "Save Settings" button to save the settings. e "Stop Communication" button This button can be clicked during communication with the VB-C50Fi to cut the connection. r Output Name Settings Select an External Device Output 1-3 and enter an External Device Output Name. t Operation settings Select the number of the setting you want to use. y Output to External Device Perform output to the selected external device. u Output Time Set the length of time for output to the selected external device, to a maximum of 23 hours, 59 minutes and 59 seconds. i Repetition Interval Set the interval at which output is to be executed, to a maximum of 23 hours, 59 minutes and 59 seconds. 4-52 Schedule Setting Tool Setting Up External Device Output 1. [. . . ] 1-4 Viewer for PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5, 7-6 Hardware and Software Requirements . . . . . . . . . . . . . . . . 1-4 Viewer Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Appendix W Web page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]