User manual CANTON VENTO REFERENCE MANUAL

[. . . ] Every detail is meticulously thought-out and all speaker components represent the utmost in acoustic and technical quality, guaranteeing maximum listening pleasure and long service life. the physical properties and materials of all speaker drivers have been optimized to reflect the latest state of the art. Thanks to special simulation software, a previously unattainable degree of perfection has been achieved. Integrated in the development process were calculations of effects resulting from changes in geometry and materials. [. . . ] To reach its maximum efficiency a loudspeaker needs a runningin period of approx. In this time the characteristics of all mechanical parts change until they reach the values specified during the development of the loudspeaker, i. Switch-off your amplifier before connecting the speakers to it. You will find the connector terminal on the rear of your Canton speakers. In order to make it easier to distinguish plus (+) from minus (-) the screwclamps on the back of the loudspeaker (plus = red, minus = black) as well as the screwclamps of your amplifier or receiver differ in color or are marked with a symbol. also the two conductors of the loudspeaker cable differ in color , form or marking. Different polarity between the left and the right channel lead to sound falsifications. For a better understanding please check the operating instructions of your controller. The Vento Reference are equipped such that you can connect the tweeter/midrange chassis and the woofer chassis separately to two respective amplifiers (bi-amping), or at least via two separate connecting cables (bi-wiring). For this purpose these speakers are fitted with a dual terminals set. The upper pair of sockets is intended for the treble/midrange frequencies, and the bottom pair for bass frequencies. These two terminal pairs have been linked with jumpers in the factory for normal operation with a single connecting cable. 2), otherwise the connected apmlifieres might be damaged. For this purpose, release the terminal screws and remove the jumpercables. The Vento Reference needs a wall distance from 20 cm (7. 9") to 1 meter (3 feet) and an angle of 0° to 5° inwards. Decide for yourself which position pleases you best. The "stereo triangle" is a good rule of guidance for optimum positioning of your new Canton speakers (Fig. This means that the best performance is usually obtained when the two speakers and your favourite listening position lie at the corners of an equilateral triangle. For decoupling the speakers from the floor your Vento Reference are provided with self-adhesive rubber pucks and metal spikes. [. . . ] 1) Midrange: 180 mm (7") aluminum membrane with , , Wave" surround 3 2) Tweeter: 25 mm (1") aluminum-manganese dome, vibration-damped 3) Woofer: 310 mm (12") aluminum membrane with , , Wave" surround 4 4) Enclosure: 4-chamber system in asymmetric design 5) Integrated loudspeaker base plate with shock absorbers 5 6 6) Mitteltonchassis: 180 mm Aluminium Membran mit Wave-Sicke 7) Hochtonchassis: 25 mm Alu-Mangan Kalotte, schwingungsgedämpft 8) Tieftonchassis: 200 mm Aluminium-Membran mit Wave Sicke 8 9) Gehäuse: 4-Kammersystem in asymmetrischem Aufbau 10) Intergrierter Lautsprecherfuß mit Schock Absorbern 8 6) Midrange: 180 mm (7") aluminum membrane with , , Wave" surround 9 7) Tweeter: 25 mm (1") aluminum-manganese dome, vibration-damped 8) Woofer: 200 mm (8") aluminum membrane with , , Wave" surround 9) Enclosure: 4-chamber system in asymmetric design 10 10) Integrated loudspeaker base plate with shock absorbers In addition to guarantee rights under statutory law, Canton grants a five-year warranty on the Vento Reference speaker. The guarantee period commences on date of purchase and applies only to the initial purchaser. Not covered by the guarantee are transport damage and damage caused by improper handling/use. The claim period shall not be extended by the replacement of parts or components within the term of the guarantee. [. . . ]