User manual CARDO SCALA-700

[. . . ] GENERAL INSTRUCTIONS All headset functions are controlled either by: · Pressing the Control Button either for a short period of less than a second, or a long period of over three seconds, Or · Moving the Wheel up or down, or by pressing it inwards. 2 scala-700 TM TURNING THE HEADSET ON FOR THE FIRST TIME In order for your headset to work with your cellular phone, they must first recognize each other. This process is called "pairing", and only needs to be performed once for each phone. To initiate pairing, press the Wheel for at least 8 seconds while the headset is turned off. The Status Light will flash red and blue indicating that the headset is in pairing mode. [. . . ] Short press the Wheel During an active call and one call on hold or waiting, short press the Wheel. During an active call and one call on hold, long press the Wheel Reject an incoming call Terminate a call Increase the volume Decrease the volume Mute/Un-mute Transfer a call to the phone Voice Dial Redial Accept call waiting or swap between calls Conference call 5 scala-700 TM FUNCTIONS (continued) DESIRED RESULT: Locate the headset (Buzzer Function) REQUIRED ACTION: Activate the Buzzer as follows: Dial a call with the mobile phone and press Send/Talk. While the call is in progress, begin pressing the mobile phone volume buttons up, then down repeating the up/down sequence four or more times. In standby, simultaneously press the Wheel and the Control button for at least 3 seconds. Lock/Unlock buttons BATTERY MONITOR To check the status of the headset's battery, press the Control Button for at least 7 seconds while the headset is on Standby position. The Status Light will flash for 2 seconds as follows: · Blue · Red and Blue · Red Fully charged Medium charge Weak charge DISABLING / ENABLING THE STATUS LIGHT To disable/enable the Status Light, while the Headset is on Standby, move the Wheel down and hold for at least three seconds. The Status Light will stop/begin flashing, depending on whether you are disabling/enabling the Status Light. 6 scala-700 TM CHANGING THE WHEEL ORIENTATION When changing volume, the default configuration of the headset is for it to be worn on the right ear. This means that clicking up on the Wheel towards the small `+' sign on the headset increases the volume one step at a time, while clicking down towards the `-' sign on the headset decreases the volume one step at a time. If you wear the headset on your left ear, this headset allows you to change the Wheel orientation from right to left ear, so that pressing the Wheel up still increases the volume, and pressing down decreases the volume. In order to set the headset for left ear orientation: Power on the Headset by pressing and holding the Control button while pressing in and holding the Wheel for 4 seconds. Once you see 3 blue flashes, the headset is powered on and you may release the buttons. NOTE: The headset will revert to its default right ear configuration once it is turned off. In order to regularly use the headset in left ear configuration, always turn on the headset using the Control + Wheel procedure above. NOTE: If you choose to wear the headset on your left ear but do not with to change the Wheel orientation, the Wheel will function in the reverse order, i. e. turning down will increase volume, turning up will decrease volume. 7 scala-700 TM LOCATE THE HEADSET (Buzzer Function) The scala-700 allows you to locate the headset by activating a buzzer. Activate the Buzzer as follows: Dial a call with the mobile phone and press Send/Talk. While the call is in progress, begin pressing the mobile phone volume buttons up, then down, repeating the up/down sequence four or more times. The headset will start buzzing. STATUS LIGHTS The Headset uses the following Status Lights to display its status Status Light Status None 3 blue flashes 3 red flashes Alternating Red/blue flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Steady red Headset is off or Status Light is disabled Powered on successfully Powered off successfully Pairing mode Standby ­ No call in progress Call being initiated or in progress Standby and battery is low Call being initiated or in progress and battery is low Headset is being charged 8 scala-700 TM AUDIO TONES With the exception of the actions described in the following table, all actions are followed by a single tone to confirm that the headset has accepted the action. Action Mute Volume up Volume down Locate the headset Tone On/off tone and mute reminder tone every 20 seconds Tone on maximum volume Tone on minimum volume Buzzing TROUBLESHOOTING Note: For most problems, it is recommended as a first step that you turn the headset off for 20 seconds and then on again. If this does not help, try pairing the headset and phone again. Problem Action Pairing fails 1. Delete scala-700 from your paired device list in your phone (if it is listed). Take the battery out of the phone and put it back. Repeat the pairing process as described in TURNING THE HEADSET ON FOR THE FIRST TIME section above. 9 scala-700 TM Can't answer phone calls or (Assuming your mobile phone supports perform voice dialing Voice Dialing) : 1. [. . . ] When the headset is fully charged, the red light turns off. Possibly caused by nearby interference 2. If you have a GSM phone and your headset is too close to the phone, interference may occur. Headset and mobile phone are more than 30 ft. [. . . ]