User manual CARDO SCALA-RIDER TEAMSET

[. . . ] Connect the wall charger to the headset's Charging Jack (located between the two Volume buttons). While charging, the red Status Light illuminates (it may take up to 15 seconds until the red Status Light illuminates). When charging is complete the Status Light will turn off. GENERAL INSTRUCTIONS All headset functions are controlled either by: · Pressing the Control or Intercom Button either for a short period of less than a second or a long period of over three seconds Or · Short pressing the volume up and volume down buttons. 4 TURNING THE DRIVER HEADSET ON FOR THE FIRST TIME The driver unit (yellow logo): The driver unit permits two communication modes: · Mobile Phone connections with third parties · Intercom connection with the passenger In order for the headset to work with your cellular phone, they must first recognize each other. [. . . ] Adjust the clamp's location so that the microphone is located in front of your mouth, and then tighten the screws. Attach the speakers to the Velcro inside your helmet opposite your ears (short speaker cord for left ear & long speaker cord for right ear), or use the supplied Velcro pad. Allen Wrench Back Plate CORRECT INCORRECT NOTE: The microphone must be positioned vertically and not horizontally. 7 4. Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place. REMOVING THE HEADSET FROM THE HELMET Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand. We recommend that you store your headset in the enclosed carrying pouch when not in use. Press here to remove 8 DRIVER'S UNIT FUNCTIONS DESIRED RESULT: G E N E R REQUIRED ACTION: A L F U N C T I O N S Turn on the headset Turn off the headset Increase the volume Decrease the volume P H O N Press the Control Button steadily for at least 6 seconds Press the Control Button steadily for at least 3 seconds Short press the Volume Up Button. Short press the Volume Down Button. E F U N C T I O N S Answer a call Reject a call Terminate a call Voice Dial Redial Enable/Disable voice command feature Short press the Control Button or speak loudly any word of your choice. Short press the Intercom Button or remain silent for 15 seconds. For some mobile phones you may need to press the Control Button to end the call. During standby, short press the Control Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. During standby, long press the Intercom Button Long press the volume up and down buttons simultaneously until you hear a beep. The default status is voice command enabled. 9 DRIVER'S UNIT FUNCTIONS (continued) DESIRED RESULT: I N T E R C REQUIRED ACTION: O M F U N C T I O N S Start using the intercom Terminate the operation of intercom Conference Call (add passenger to an active call) End Conference Call (release passenger from a conference call) DESIRED RESULT: Turn on the headset Turn off the headset Start using the intercom During standby, start speaking loudly to activate the intercom Stop speaking. The audio connection will be terminated within 25 seconds. During an active phone call, tap the Intercom Button. During a conference call, tap the Intercom Button. PASSENGER'S UNIT FUNCTIONS REQUIRED ACTION: Press the Control Button steadily for at least 3 seconds Press the Control Button steadily for at least 3 seconds During standby, start speaking loudly to activate the intercom Terminate operation Stop speaking. The audio connection will be terminated of intercom within 25 seconds. Enable/disable During standby, short press the Control Button. Always On Intercom One tone = Always On intercom. Two tones = Voice Controlled (VOX) intercom Increase intercom volume Short press Volume Up Button Decrease intercom volume Short press Volume Down Button 10 DRIVER'S UNIT STATUS LIGHTS The Driver Headset uses the following Status Lights to display its current state: Status Light None Alternating Red/blue flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Steady red Status Headset is off Pairing mode Standby ­ No call is in progress Call being initiated or in progress Battery is low Call being initiated or in progress and battery is low Headset is being charged PASSENGER'S UNIT STATUS LIGHTS The Passenger Headset uses the following Status Lights to display its current state: Status Light None One blue flash every 3 seconds Steady red Status Headset is off Headset is on Headset is being charged 11 AUDIO TONES With the exception of the actions below, all other actions are followed by a single tone to confirm that the headset has accepted the command. Action Enable/Disable Always On intercom Intercom on other side is not enabled or off and you start speaking Tone One tone = Always On intercom Two tones = Voice Controlled (VOX) intercom 2 beeps to alert you that the other side is not available TROUBLESHOOTING Problem Action Phone-Related Problems (Driver Unit with Bluetooth Phone) Unsuccessful Bluetooth Pairing 1. [. . . ] When the headset is connected to the charger and it is fully charged, the red Status Light turns off. You may have inadvertently left the Always-On Intercom on. Reject feature works only with mobile phones that support Bluetooth hands-free profile. [. . . ]