User manual CARVIN 742-742P-V1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual CARVIN 742-742P-V1. We hope that this CARVIN 742-742P-V1 user guide will be useful to you.

Lastmanuals help download the user guide CARVIN 742-742P-V1.


Mode d'emploi CARVIN 742-742P-V1
Download
Manual abstract: user guide CARVIN 742-742P-V1

Detailed instructions for use are in the User's Guide.

[. . . ] The 742 is our top of the line 15" monitor speaker designed to cut through on any stage. This monitor will easily handle 400 watts and at the same time offer studio quality sound even when pushed to extreme levels. Because of it's controlled dispersion, feedback problems are minimized. RECEIVING INSPECTION INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during shipping. If any damage is found, please notify the shipping company & CARVIN. [. . . ] Never direct the microphone towards the speaker. For greater coverage, add additional monitors. 742 FREQUENCY RESPONSE WARRANTY Parts and labor are covered for 1 year on manufacturer's defects. Warranty does not cover burned out drivers caused by excessive power or distortion, or physical damage caused by general use, moisture or dust. CAUTION: Distortion from power amps can destroy drivers much faster than clean power. Contact Carvin's Customer Service at 800-854-2235 or returnsrepairs@carvin. com. Customer is responsible for shipping charges. MODEL 742 SPEAKER SYSTEM SPECS: TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS Individual speaker or speaker cabinet wiring examples for total impedance. 8 TOTAL IMPEDANCE + + SERIES CONNECTION 16 TOTAL IMPEDANCE + + PARALLEL CONNECTION 4 TOTAL IMPEDANCE + + SERIES/PARALLEL CONNECTION 8 TOTAL IMPEDANCE + + 8 8 + + + 8 8 8 16 8 4 8 8 + 8 + 8 8 For your records, you may wish to record the following information. Serial No. _____________________ Invoice Date_______________ Frequency Response: Useable Low Frequency: Power Handling: Recommended Amp: Sensitivity: Coverage Angles: Imp: Horn Driver Protection: Inputs/Outputs: Woofer Enclosure Type: Enclosure Covering: Dim/Wt: Warranty: Options: 65 Hz to 17 kHz ±3 dB 42 Hz (-10 dB) 400w Continuous Power 5 to 600 watts 101 dB SPL, 1 Watt @ 1 meter 90° Horizontal, 45° Vertical 8 Yes Two 1/4" Closed Box Black Duratuff IITM 20"W x 14"D x 26"H, 46lbs. One Year Cover: CVS742 c 12340 World Trade Drive, San Diego, CA 92128 (800) 854-2235 www. carvin. com 76-00742 0902 742P POWERED SPEAKER INPUT INSTRUCTIONS For any distance over 25', use a balanced source. Use the balanced XLR or 1/4" connectors featured on the rear connect plate. You may DAISY-CHAIN as many speakers as you wish. All connectors are wired in parallel. 12dB PAD To start the initial hook up, be sure the 12dB pad switch is in the "IN" position. This will be the least sensitive position for your input source. If your signal is weak, depress the Pad switch to the "OUT" position, which will raise the level of your powered speaker. SOFT LIMITING Unlike other limiters, the SPSTM incorporates an exclusive optoisolater limiter system, which does not add distortion when limiting. Soft limiting starts to occur when you approach the maximum output of your powered speaker allowing you to get more usable power out of your system without severe clipping. However, when you hear distortion, hard clipping or cutting out, reduce the overall level as you have exceeded the system's capacity. POWER/PROTECT When the system has been activated by the power switch, the LED will indicate GREEN. If the system should go into protect, the LED will indicate YELLOW which may occur if; a) one of the internal drivers short or b) if the power amp should require service. AC POWER The 742P is available in either 120V or 240V models. Always use dedicated circuits for powered speakers. Every Carvin SPSTM powered speaker is designed to be left on continuously in the case of permanent installations. 742P Read general information about the 742 enclosure for specs, warranty and precautions on the other side. REAR POWERED CONNECT PLATE MADE IN THE USA Serial No. SPSTM POWERED SPEAKER FEATURES Carvin's SPSTM SMART POWERED SPEAKERSTM are more than just another "power amp in a cabinet". They offer advanced electronics to perfectly control every speaker component. Woofers are power-managed through active filtering, allowing more low-end punch and preventing over excursion. [. . . ] Daisy-chain as many powered speakers as you need for additional coverage. A 12 dB gain switch matches every audio source. A removable AC cord frees the enclosure when transporting. PRO SOUND REINFORCEMENT POWER 300 Watts CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN 742P CAUTION - TO PREVENT ELECTRICAL SHOCK DO NOT DEFEAT THE SAFETY GROUND ON THE POWER CORD - DO NOT REMOVE COVER . WARNING - TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE TO RAIN OR MOISTURE. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CARVIN 742-742P-V1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual CARVIN 742-742P-V1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag