User manual CARVIN C44

[. . . ] This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. LIMITED WARRANTY Your Carvin mixer is guaranteed against failure for 1 YEAR unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. [. . . ] This provides two simultaneous effects per channel and the use of MON 4. 13. CHANNEL SIGNAL GREEN LED The SIGNAL LED is pre-fader and post EQ. This LED helps the operator verify that the channel is receiving a signal from the mic or instrument inputs even when the channel fader is off. CHANNEL PEAK RED LED This peak indicator is pre-fader and post EQ. If the PEAK LED flashes, the channel needs a reduction with the GAIN control (#4)to prevent distortion. A "solid" lit PEAK LED indicates that the channel has been MUTED. MASTER SECTION 20. TWO STEREO 24-BIT EFFECTS The internal 24-BIT stereo processors receive signals from the EFF 1 / EFF 2 channel controls. If the adjacent PK (peak) LED flashes, reduce the level from the channel EFF 1 / EFF 16. A "solid" PK LED will show EFFECTS 1 or 2 have This switch allows the operator to listen to a channel (pre been muted, either by the MUTE switches or by the optional fader listen) in the headphone mix to set tone and gain levels FS22 footswitch (#41). The RETURN control will adjust the as well as see the channel at the LED meter output (#32). CHANNEL ASSIGNMENT SWITCHES has its own EFFECT send that will send the signal to the effects These switches assign the channels' signal to the Master L/R processors. The red PK LED will indicate when the effects signal faders, or to the SUB-GROUP faders 1 & 2, 3 & 4 for subfrom the channel is distorting. Reduce the level of the chanmixing in stereo pairs. For mono, PAN fully to the left and nel EFFECT control until the PK LED stops flashing. assign a channel to Sub-Group fader 1 or 3 only. PAN fully EFFECT AND PARAMETERS to the right and assign a channel to Sub-Group fader 2 or ECHO: When the SELECT control is at the "7 O-clock" posi4. Likewise assigning the L/R switches sends the channel tion, it is selected to the first ECHO setting where you get a single directly to the main L or R faders. Turning the PARAMETER control to 1 will provide the short42 44 43 41 40 est delay time between the original 39 signal and the echo. Increasing the EFF SW 1-2 PHONES GROUPS PARAMETER control to the right 14 15 16 will increase the time delay between L the original signal and the echo. To 1 2 3 4 TAPE OUT 45 MON 1 MON 2 MON 3 MON 4 increase the number of echo repeats, L RR turn the SELECT control clockwise to "9 O-clock" (maximum regenerEFF 1 EFF 2 3L RETURN 3R TAPE IN MONO RTN 4 46 ation). REVERB: When the SELECT control 38 is at the "10 O-clock" position, it is 37 selected to the first REVERB setting. 36 POWER +12 12+ Turning the SELECT control clock8 8 EQ 1 EQ 2 35 4 4 wise will increase the amount of high 0 0 33 4 4 8 8 frequencies in the reverb. [. . . ] Most external equipment is not set up for the TRS plug directly so an adapter cable is required. The adapter cable will have on one end the TRS plug and two mono plugs either male or female on the other end. The two plugs each have the ground connected to the sleeve, one has the return on its tip and the other has the send on its tip. This allows the send to be connected to the input of the external equipment and the return to its output completing the insert loop back to the channel. LINE HALF INSERT DIRECT OUT FULL INSERT TIP: SEND RING: RETURN SLEEVE: GROUND 1/2 INSERT LINE TIP: SIGNAL SLEEVE: GROUND 1 PIN 2 (+) PIN 3 (­) MIC MIC Pre-Amp GAIN INSERT GAIN 456 3 7 2 8 1 9 0 10 HI -0+ 3 3 6 6 9 12 MID 6 9 3 12 -0+ 3 6 9 9 INSERT JACK STEREO PLUG 12 12 LOW - 0 + 3 3 6 6 9 12 12 9 SEND RETURN TO EFFECTS The "half" insert connection creates a send signal without breaking the channels signal path. [. . . ]