User manual CARVIN XC3000

[. . . ] CARVIN ENGINEERING DATA CHANNEL ONE 0dB 0dB OFF 40Hz XC3000 STEREO 2/3-WAY ELECTRONIC CROSSOVER CHANNEL TWO FREQUENCY FREQUENCY 2. 0 x1 x10 OPERATING MANUAL ON 2. 0 3. 0 5. 0 7. 0 PWR 0dB 0dB XC3000 24dB/OCTAVE +6 PEAK GAIN 200 90 300 450 600 3. 0 5. 0 7. 0 0dB OFF 40Hz 0dB 0dB 0dB 200 90 300 450 600 x1 x10 0. 8 0. 8 +6 +6 MID LEVEL +6 HIGH LEVEL HIGH LEVEL 50 Hz 1k 0. 6 kHz 10 MID / HIGH 3 WAY 2 WAY +6 PEAK GAIN +6 SUB SONIC LOW LEVEL LOW LEVEL +6 MID LEVEL +6 HIGH LEVEL HIGH LEVEL 50 Hz 1k 0. 6 kHz 10 MID / HIGH 3 WAY 2 WAY Stereo 2/3Way SUB SONIC LOW LEVEL LOW LEVEL Crossover LOW / MID LOW/HIGH LOW / MID LOW/HIGH OFF Congratulations on your purchase of the CARVIN XC3000 Stereo 2 / 3 - way Electronic Crossover. The XC3000 was designed with the professional in mind. Your unit has been engineered and assembled in the U. S. A. , using only high quality electronic components and uncompromising workmanship. The XC3000 provides the best available crossover networks consisting of a forth-order statevariable implementation of Linkwitz-Riley crossover alignments. [. . . ] POWER SWITCH Push this switch vertically to the "on" position to apply power to the unit. The power indicator LED will light to show that the XC3000 is on. CHANNEL TWO The controls of Channel "TWO" are identical to the controls of Channel "ONE". REAR PANEL FEATURES 1 1-800-854-2235 www. carvin. com SERIAL NUMBER 5 3 4 6 2 7 8 9 MONO SWITCHABLE TO MONO [ LOW 1+2 ] Electronic Crossover [ LOW 1+2 ] XC3000 THE INPUT GND LIFT INPUT HIGH PHASE INTERNAL FUSE 90-250 VAC 10 VA 50-60Hz MADE IN USA CHANNEL ONE MID PHASE LOW PHASE CHANNEL TWO HIGH PHASE MID PHASE LOW PHASE 1. LINE CORD All Carvin equipment is supplied with 3 conductor line cords for maximum safety, greatly reducing the chance of electrical shock. If the XC3000 unit is to be plugged into a (2) prong outlet, use a quality 3 to 2 prong grounded adapter. Do not defeat the grounding pin of your AC line cord as this is for your protection. GROUND LIFT SWITCH Useful in getting rid of ground loop buzzing. This switch lifts the grounds on the nputs and outputs. BALANCED XLR INPUT Offers the best connection to the XC3000. The XLR connector wiring is as follows: Pin #1 ground, Pin #2 Positive Balance, Pin #3 Negative Balance. BALANCED 1 / 4" PHONE INPUT The balanced 1 / 4" phone input jack will accept either balanced or non-balanced connections. For best results use balanced (Tip, Ring, Sleeve) connections to reduce cable hum. PHASE INVERTER SWITCH The PHASE inverter switch gives you the option of inverting the phase of each of the main output to correct any phase inversion problem at your speakers or power amps. 6. LOW OUT XLR The LOW OUT 1 / 4" phone jack provides a balanced output for the low pass filter of the channel. This is where you connect the power amp that will be driving your bass cabinets. MID OUT XLR The MID OUT 1 / 4" phone jack provides a balanced output for the band pass filter of the channel. This is where you connect the power amp that will be driving your mid range cabinets. HIGH OUT XLR The HIGH OUT 1 / 4" phone jack provides a balanced output for the high pass filter of the channel. This is where you connect the power amp that will be driving your high frequency horns or tweeters. MONO (LOW 1+2) SWITCH Combines both signals from each channel's low pass filters. This is where you would connect a power amp to drive a mono subwoofer sustem. BI-AMPLIFYING WITH THE XC3000 MONO BI-AMP CONFIGURATION System Requirements: A) Mono source (Mixer) B) One Stereo Power Amp C) Individual Horn and Woofer Connections STEREO BI-AMP CONFIGURATION System Requirements: A) Stereo source (Mixer) B) Two Stereo Power Amps C) Individual Horn and Woofer Connections Set the intput "GAIN" so that the "PEAK" LED does not illuminate. Simply plug your full range frequency source into the "CHANNEL ONE" 1/4 " PHONE or XLR input connector at the rear panel of the XC3000. [. . . ] CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. Carvin assumes no responsibility for horn drivers or speakers damaged by this unit. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. [. . . ]