User manual CASABLANCA FAN COMPAGNY LEGRANDE

[. . . ] L E GRANDE OWNERS MANUAL CONTENTS INTRODUCTION . 4 CONTROL FEATURES: VERSA TOUCH OPERATION . 10 READ AND SAVE THESE INSTRUCTIONS SAFETY FIRST Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's manual completely and carefully. Retain this manual for future reference. [. . . ] If it is not, a new box must be installed. NOTE: The fan weight is 23 pounds. 3 CEILING HARDWARE ADDITIONAL HARDWARE 2 1/4 x 8-32 ROUND HEAD SCREWS (2) 1 x 8-32 ROUND HEAD SCREWS (2) FLAT WASHER (2) CROSSBAR MOUNTING BRACKET WIRE NUT (4) CROSSBAR MOUNTING BRACKET INSTALLATION Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED WIRING BOX CEILING WIRING CROSSBAR MOUNTING BRACKET RIDGE SIDE DOWN FLAT WASHER GREEN GROUND WIRE APPROVED OUTLET BOX HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY LOCK WASHER (4) CANOPY 4 CANOPY INSTALLATION Step 2. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Note: On sloped ceilings, align the canopy opening towards the top or room peak. CROSSBAR MOUNTING BRACKET CANOPY CANOPY LOCK WASHER CANOPY SCREW HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. Rotate the fan body until the slot in the nylon ball fits into the pin opposite the canopy opening. BALL NOTE: The fan weight is 23 pounds. SLOT PIN CANOPY ELECTRICAL CONNECTIONS Step 4a. Attach the fan wires to the ceiling fixture outlet box wiring by twisting the bare ends of the wires together and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Wiring Connections · GREEN leads from mounting plate and fan to GROUND conductor of power source. · WHITE wire from fan to white NEUTRAL wire in ceiling fixture outlet box. · BLACK power wire from fan to BLACK power wire in ceiling outlet box. Secure with wire nut. WIRE NUT 2 BLACK WIRES 2 WHITE WIRES 3 GREEN WIRES 5 CANOPY HATCH INSTALLATION Step 5. Tuck the wires into the canopy with the wire nuts pointed upwards, so that the WHITE and BLACK wires are on opposite sides of the canopy and all wires are clear of the canopy opening. Install canopy hatch with the last canopy screw and lock washer. To do this, tilt the fan body away from the hatch opening. Tighten the screws firmly by hand only, Step 7. Straighten the fan, then check to ensure that there is no movement between the canopy and ceiling or Hang-Tru ball and top support shaft. CANOPY HATCH LOCK WASHER CANOPY SCREW TILT THE FAN TO INSTALL LAST CANOPY SCREW Note: Write down the Serial Number and the model number for future reference. BLADE HARDWARE BLADE SCREW BLADE WASHER BLADE HOLDER BLADE ATTACH BLADE HOLDERS Step 8. Attach the blades to the blade holders by aligning the screw holes of the holder with the holes of the blade. [. . . ] Exceeding the rated maximum allowable wattage for the fan will burn out the fan electronics module and void the warranty. PROBLEM PROBLEM FAN WILL NOT START VERSA·TOUCH POSSIBLE REMEDIES POSSIBLE REMEDIES. . -Check main circuit fuses, circuit breakers, or wall switch position. Check all wire connections, making sure the power is turned off during this inspection. -Pin connectors are not making good contact. Release lockpin and check pins at end of downrod & inside coupler and also 9 pin connector under cover. [. . . ]