User manual CASABLANCA FAN COMPAGNY UTOPIAN

[. . . ] The maximum current requirement for the fan with light fixture is 3. 8 amps. Maximum light current is 2. 8 amps or 340 watts of lighting. · Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make sure all wires are within the canopy and that no wires are being pinched. [. . . ] Contact your local Authorized Casablanca Dealer in regards to purchasing a "Slope Ceiling Adaptor. " 2 UTOPIAN PREPARATION INSTRUCTIONS Unpacking: Before assembling and installing your ceiling fan, remove all parts from the shipping cartons and check them against the parts listed here. Before discarding packaging material, be certain that all parts have been removed. PERMA·LOCKTM HARDWARE ALLEN SET SCREW 1 /4-20 x 1/4" (PRE-INSTALLED) 3mm ALLEN WRENCH DOWNROD & BALL ASSEMBLY FAN PREPARATION IMPORTANT SAFETY INFORMATION! BEFORE STARTING THE INSTALLATION OF YOUR CEILING FAN, INSTALL THE THREADED DOWNROD INTO THE MOTOR COUPLING AND LOCK THE ASSEMBLY Prepare for fan installation as follows: Step A. Route the wires from the motor through the Perma·LockTM downrod and ball assembly. Tip: The downrod has a tapered thread that is designed to lock completely when correctly installed. Using the provided allen wrench, loosen the set screw several turns to allow installation of the downrod. Thread the downrod into the motor coupling until it stops turning, this will take at least four and a half full turns. Securely tighten the set screw with the provided allen wrench to ensure safe operation of your fan. CAUTION: Failure to fully lock in the downrod before securely tightening the allen set screw may cause the fan to separate from the downrod during normal operation! MOTOR WIRES GROUND WIRE DOWNROD & BALL ASSEMBLY TAPERED THREAD ALLEN SET SCREW MOTOR COUPLING 3 UTOPIAN CEILING HARDWARE ADDITIONAL HARDWARE 21/4 x 8-32 ROUNDED HEAD SCREW (2) 1 x 8-32 ROUNDED FLAT WASHER (2) HEAD SCREW (2) CROSSBAR MOUNTING BRACKET WIRE NUT (4) GETTING STARTED Installing a New Ceiling Fixture Outlet Box If you do not have an existing fixture located where you wish to place your Casablanca fan, an approved ceiling fixture outlet box must be installed and wired. Warning: To reduce the risk of fire, electrical shock, or personal injury, mount to outlet box marked acceptable for ceiling fan support using the mounting hardware provided with the outlet box. Using Existing Ceiling Fixture Outlet Box After turning the power OFF at its source (either circuit breaker or fuse box), lower the old fixture and disconnect the wiring. Check the ceiling fixture outlet box to be sure that it is marked `Approved for ceiling fan mounting'. If it is not, a new box must be installed. CROSSBAR MOUNTING BRACKET INSTALLATION WARNING: Damp Location rated fans require a Ground Fault Interrupter (GFI). Use a weather-proof outlet box, properly connect ground wires, and use only under a weather-proof structure. Proceed with installation as follows: Step 1. Route the wires from the ceiling outlet box through the crossbar mounting bracket center hole. Attach the bracket, with ground wire and ridges down, to the ceiling fixture outlet box with the mounting hardware included with the outlet box. Using the screwdriver, tighten the screws firmly by hand only, being careful not to bend the bracket by over tightening. CAUTION: To reduce the risk of personal injury, use only the mounting hardware provided with the approved outlet box to install the crossbar mounting bracket. CEILING FAN APPROVED OUTLET BOX CEILING WIRING CROSSBAR MOUNTING BRACKET FLAT WASHER RIDGE SIDE DOWN GREEN GROUND WIRE OUTLET BOX MOUNTING HARDWARE CANOPY HARDWARE CANOPY SCREW (4) CANOPY HATCH CANOPY CANOPY LOCK WASHER (4) 4 UTOPIAN CANOPY INSTALLATION Step 2. Thread the wires from the ceiling through the opening in the canopy. Attach the canopy to the crossbar mounting bracket with three of the 8-32 x 21/4 long canopy screws and canopy lock washers. Using the screwdriver, tighten the screw firmly by hand only. CANOPY CROSSBAR MOUNTING BRACKET INSTALLED Note: On sloped ceilings, align the canopy opening toward the top or room peak. CANOPY LOCK WASHERS CANOPY SCREWS HANGING THE FAN Step 3. To hang the fan body in the canopy, hold the fan body firmly and insert the ball into the canopy opening. [. . . ] Check the screws holding the blade holders to the flywheel (or direct drive motor). Check that bladeholders have not been bent during installation. Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s) as neccessary. Tighten the blade to bladeholder screws. [. . . ]