User manual CASIO 2762

[. . . ] MO0404-EA Operation Guide 2762 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully and keep it on hand for later reference when necessary. · This watch does not have a time zone that corresponds to the Greenwich Mean Time differential of ­3. 5 hours. Because of this, the radio-controlled timekeeping and Dual Time functions will not display the correct time for Newfoundland, Canada. [. . . ] · Alarm and Hourly Time Signal operations are performed in accordance with the Timekeeping Mode digital time. · Pressing any button stops the alarm tone operation. · Performing any one of the following operations during a 5-minute interval between snooze alarms cancels the current snooze alarm operation. Displaying the Timekeeping Mode setting screen Displaying the snooze alarm (AL5) setting screen Daylight Saving Time (DST) Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time. Remember that not all countries or even local areas use Daylight Saving Time. The time calibration signals include both Standard Time and DST data. When the auto DST setting is turned on, the watch switches between Standard Time and DST (summer time) automatically in accordance with the signal it receives. · The auto DST setting can be turned on only while ­5. 0, ­6. 0, ­7. 0, ­8. 0, ­9. 0, ­10. 0, +8. 0, or +9. 0 is selected as the Home Time Zone. · If you experience problems receiving the time calibration signal in your area, it is probably best to switch between Standard Time and Daylight Saving Time (summer time) manually. To test the alarm In the Alarm Mode, hold down B to sound the alarm. To turn an alarm and the Hourly Time Signal on and off 1. In the Alarm Mode, use B to select an alarm or the Snooze alarm indicator Hourly Time Signal. Press A to toggle it on (on displayed) and off (oF displayed). · You need to display the screen of a daily alarm (AL1 to AL5) or the Hourly Time Signal in order to check its current on/off status. · Turning on the snooze alarm displays the snooze alarm On/Off status indicator on its Alarm Mode screen and in all modes. · The snooze alarm indicator flashes during the 5-minute intervals between alarms. Hourly Time Signal Screen To change the Daylight Saving Time (summer time) setting 1. While any screen other than the last signal screen is on the display in the Timekeeping Mode, hold down A until the GMT differential value starts to flash, which indicates the setting screen. Press C to display the DST setting screen. Press D to cycle through the DST settings in the sequence shown below. Auto DST (A) DST off (OFF) DST on (on) 4. · The DST indicator appears on the display to indicate that Daylight Saving Time is turned on. Analog Timekeeping The analog time of this watch is synchronized with the digital time. The analog time setting is adjusted automatically whenever you change the digital time. Note · The hands for the analog timepiece move to adjust to a new setting whenever any of the following occurs. When you change the digital time setting manually When the digital time setting is changed by time calibration signal reception When you change the Home Time Zone and/or DST setting · Whenever you need to adjust both the digital and the analog time settings manually, make sure you adjust the digital setting first. [. . . ] This sound is caused by mechanical operation of the auto light switch, and does not indicate a problem with the watch. Tachymeter Tachymeter bezel 60 TACH YME T 360 ER 80 70 70 10 0 120 0 15 Power Saving When turned on, Power Saving automatically enters a sleep state whenever the watch is left for a certain period in an area where it is dark. The table below shows how watch functions are affected by Power Saving. · There are actually two sleep state levels: "display sleep" and "function sleep". Elapsed Time in Dark 3 to 4 days (Display Sleep) 8 days or more (Function Sleep) Operation Digital display off, but all functions enabled · Digital display off · All functions, including analog timekeeping, disabled · Internal timekeeping maintained · The illustration shows an example where it took 50 seconds to travel one kilometer by car. [. . . ]