User manual CASIO 3354

[. . . ] MO0804-EA Operation Guide 3353 3354 5053 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to carefully read this manual and keep it on hand for later reference when necessary. Keep the watch exposed to bright light Bright Light l l lllllllll Solar cell The electricity generated by the solar cell of the watch is stored by a built-in battery. Leaving or using the watch where it is not exposed to light causes the battery to run down. Make sure the watch is exposed to light as much as possible. [. . . ] This helps to keep the rechargeable battery from going dead. Stopwatch 1/100 Seconds second To check the current battery level In the Timekeeping Mode, press C once to display the battery level indicator. · The battery level indicator shows the battery level either as HI (Level 1) or MID (Level 2). · If the battery level drops below Level 2 (MID), a charge soon alert (Level 3) is displayed in all modes. Battery level indicator The stopwatch lets you measure elapsed time, split times, and two finishes. · The display range of the stopwatch is 99 minutes, 59. 99 seconds. · The 1/100-second value appears while the elapsed time operation is stopped or while a split time is frozen on the display. Elapsed Time Screen Elapsed time (Minutes : Seconds) 1/100 second More than one minute Battery Level Indicator and Charge Indicator The battery level indicator shows you the current power level of the rechargeable battery. Level Split Time Screen Split time Minutes Seconds Split indicator (Minutes : Seconds) ||| 1/100 second ||||| || || (Charge Soon Alert) 4 |||| · The stopwatch continues to run, restarting from zero after it reaches its limit, until you stop it. · Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time and returns to elapsed time measurement. · The stopwatch measurement operation continues even if you exit the Stopwatch Mode. · All of the operations in this section are performed in the Stopwatch Mode, which you enter by pressing C. || llllllll 1 2 3 alarm is turned on, the alarm tone sounds when the alarm time is reached. You can also turn on an Hourly Time Signal that causes the watch to beep twice every hour on the hour. · The alarm and Hourly Time Signal operate in accordance with the current digital time. · The alarm number (AL1 though AL3) indicates an alarm screen. SIG appears in place of the alarm number when the Hourly Time Signal screen is shown. Alternate at · All of the operations in this section are performed in the two-second Alarm Mode, which you enter by pressing C. lll llllllll lll To illuminate the display In any mode, press B to illuminate the display. · You can specify 1. 5 seconds or 2. 5 seconds as the illumination duration. See "To set the current digital time and date manually" for more information. or Battery Level Indicator Function Status All functions enabled. All functions enabled. ||||| ||| || Auto and manual receive, alarm, hourly time signal, illumination, and display are disabled. Though the hands of the watch do not move, time continues to be kept internally. All functions, including timekeeping, disabled. 3 Operation Guide 3353 3354 5053 · The flashing charge indicator ( C ) at Level 3 tells you that battery power is very low, and that exposure to bright light for charging is required as soon as possible. · At Level 4, all functions are disabled and settings return to their initial factory defaults. Functions are enabled once again after the rechargeable battery is charged, but you need to set the time and date, after the battery reaches Level 2 after dropping to Level 4. [. . . ] · The second hand will move at high speed to the 12 o'clock position, where it will stop. Use D to scroll through available transmitter settings until the one you want to select is displayed. |||||| ||| ||| City Transmitter indicator To set up the watch to do this: Select this transmitter setting: Automatically select the Anthorn or Mainflingen signal AT Receive the Mainflingen signal DCF MSF Receive the Anthorn signal · Note that --- appears in place of the transmitter indicator when any city code besides LON, PAR, BER, or ATH is selected as the Home City code. This indicates that you cannot specify a transmitter. Press A twice to exit the setting screen. [. . . ]